background image

PILOT-OP-EN 

- 25 -

BATTERY MAINTENANCE GUIDE

SAFETY:

DANGER

Explosive hydrogen gas forms when Batteries are 
charging. An open fl ame or spark can cause this gas 
to explode. Serious personal injury or property damage 
could occur. Only charge the Batteries in this machine 
in a well ventilated area.

WARNING

Before you service a Battery, always wear face protec-
tion, protective gloves and protective clothing.  Battery 
acid or battery explosion can cause serious injuries.

WARNING

The Batteries in this machine produce hazardous 
voltage which can cause electrical shock, burns and/
or electrocution. Always disconnect Batteries before 
servicing this machine.

WARNING

The Batteries in this machine contain sulfuric acid, 
which causes burns to skin. If battery acid contacts 
clothing or skin, rinse the effected area with cold water 
immediately. If battery acid gets on your face or in your 
eyes, fl ush the area immediately with cold water and 
seek medical attention.

WARNING

Dress safely. Do not wear rings or metal wrist watches 
when servicing this machine, as they can cause an 
electrical short circuit which can cause serious burns.

INSPECTION AND CLEANING:

• 

Keep Batteries clean and dry from residue

• 

Check that all vent caps are tight

• 

Use a solution of baking soda and water to clean if 
acid residue on Batteries or corrosion on the terminals

• 

Protective spray of petroleum jelly should be applied to 
terminals to reduce corrosion

STORAGE:

• 

Batteries should be fully charged prior to and during 
storage

• 

Never store discharged Batteries

• 

Store Batteries in a cool, dry place but never below 
freezing - Recharge in storage a minimum of every 30 
days

• 

Recharge Batteries before putting them back into 
service

WATERING:

• 

Add water, NEVER ACID, to cells 

(distilled water 

recommended)

.

• 

Do not over water

• 

Before charging the Batteries, only add water if the 
plates are exposed.  Add just enough water to cover 
the plates, then charge the batteries.  Once fully 
charged, add water to the proper level as indicated 
below.

• 

For full charge plus series Batteries add water to the 
maximum water level indicator 

(A)

.

• 

Water watering, secure vent caps back on Batteries.

WATER LEVEL SHOULD BE 
1/8'' ABOVE PLATES

A

Summary of Contents for Pilot 24'' EDGE










































Reviews: