background image

- 14 -  

34-OP-EN

ON-BOARD CHARGER

Charger Specifi cations

• 

Output voltage of 12 Volts

• 

Output current of 25 amps max

• 

Input voltage of 110 Volts/ 60 Hz 

(220V/50 Hz available)

• 

Automatic shut off circuit

• 

Made for Deep Cycle Batteries 

DANGER

Explosive hydrogen gas forms when Batteries are 
charging. An open fl ame or spark can cause this gas 
to explode. Serious personal injury or property damage 
could occur. Only charge the Batteries in this machine 
in a well ventilated area.

WARNING

Before you service a Battery, always wear face protec-
tion, protective gloves and protective clothing.  Battery 
acid or battery explosion can cause serious injuries.

WARNING

The Batteries in this machine contain sulfuric acid, 
which causes burns to skin. If battery acid contacts 
clothing or skin, rinse the effected area with cold water 
immediately. If battery acid gets on your face or in your 
eyes, fl ush the area immediately with cold water and 
seek medical attention.

CAUTION

Always use the automatic battery charger provided by 
the manufacturer of this machine to charge the Batter-
ies of this machine. It is designed to charge the Batter-
ies at the appropriate rate. If you must use a different 
charger, disconnect the Batteries before charging to 
avoid damage to the electronic speed controller.

ON-BOARD BATTERY CHARGING:

1.  Transport machine to a well ventilated area for 

charging.

2.  Turn the machine off.  Open the Machine Hood.

3.  Check the water in each Battery 

(A)

.  Do not charge 

the machine unless the water is slightly higher than 
the plates.  If needed, add enough distilled water to 
just slightly cover the plates.  Be careful not to over fi ll.  
Batteries can overfl ow during charging.  Replace caps 
before charging.

4.  Plug the Charger power cord 

(B)

 into a grounded 

standard wall outlet 

(SEE BELOW)

.

5.  The charger will automatically begin charging and 

automatically shut off when fully charged.

6.  After the Charger has turned off, unplug the Charger 

from the wall outlet.

7.  Recheck the cell level after charging.  If needed, add 

distilled water up to the correct level.  Be certain to 
replace the caps securely and to wipe off the top of the 
Batteries with a clean cloth. 

DESCRIPTION OF LED

Red LED:

 

Battery level low

Yellow LED:

 Battery at 

1

2

 charge

Green LED:

 Battery fully charged

WATER LEVEL SHOULD BE 
1/8'' ABOVE PLATES

A

B

Summary of Contents for 34



























Reviews: