FABtotum Personal Fabricator User Manual Download Page 45 | Manualshive

Page: 45 / 123

background image

FABtotum Complete Manual

www.fabtotum.com

| 45

Customize Slicing Profiles

The Printing Head Pro main advantage is that it can print every 3D object at the first try regardless of the shape.
This does not mean that best result can be obtained from the standard profiles, but that the standard profiles usually are
the best in most situations.
Temperature and speed can be tuned, while retracts might depend on the stiffness of the material, in order to reduce
artifacts (e.g. on flexible materials).
This way the standard profiles can be tuned for speed or for quality.
All slicing profiles and onboard samples have been tested with FABtotum Official Filaments but may be as well adapted
with ease for the respective third party materials.

«
...
43
44
45
46
47
...
»

Summary of Contents for Personal Fabricator




























































































































Reviews:

No comments

Related manuals for Personal Fabricator

Brand: SA Pages: 5

Sure shot 80 tele

Brand: Canon Pages: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

Brand: Canon Pages: 2

Brand: Octave Pages: 2

Brand: Saxxot Pages: 13

Brand: Oki Pages: 2

OKIPAGE 8c Plus

Brand: Oki Pages: 48

Brand: Oki Pages: 257

Brand: Oki Pages: 113

Brand: Oki Pages: 26

Brand: Oki Pages: 183

Brand: Oki Pages: 36

Brand: Oki Pages: 136

Brand: Oki Pages: 66

Brand: Oki Pages: 123

Brand: Oki Pages: 109

Brand: Oki Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands