manualshive.com logo in svg

FABtotum Personal Fabricator, User Manual

Share
Download
FABtotum Personal Fabricator User Manual Download Page 4

FABtotum Complete Manual

www.fabtotum.com

| 4

DO NOT touch, move the product or leave it unattended when it’s operating or turned on.
DO NOT modify, disassemble or alter the unit and/or its components in any way.
DO NOT touch or bend the flexible connection cable, the connectors and all cables.
DO NOT touch contacts or the metal rods, as hands can ruin contacts and damage the metal protection layer.
DO NOT turn the product off without following the proper shutdown procedure.
DO NOT improperly dispose of the unit.

TECHNICAL SUPPORT

Our support team is always happy to assist you. Many information and solutions can be found at

http://www.fabtotum.com/knowledgebase

3D PRINTERS AND MANUFACTURING: HEALTH MEASURES

Inhalation
Heat may cause the release of irritating vapors. Milling can create and spread dust and other particles.
In case the user inhales them, they should be immediately taken to an aerated place and kept calm.
Always refer to the material datasheet.

For safety reasons some materials can’t be used for 3D printing, Milling or Laser engraving.
Check the material proprieties or consult support if unsure. Some materials, when exposed to high temperatures can
release dangerous fumes and volatile chemical elements.

Skin
Health risks related to the skin are very uncommon.
If material residue ends up on your epidermis wash the area with plenty of soap and rinse with water.
If skin rashes occur please seek medical attention.

Eyes
Health risks related to the eyes are mainly linked to the use of the laser head and are otherwise uncommon.
For some people dust may be irritating. If that happens rinse your eyes thoroughly with water. In case you are wearing
contacts, remove them and start rinsing as described above.
Use proper eye glasses for protection when operating the machine, especially when using the laser head.
Do not look directly inside the unit.

Most common symptoms and effects
Molten material may cause burns and scalds. Cutting tools may cause wounds and injuries.

Disclaimer: Manufacturer gives no warranty of merchantability or of fitness for a particular purpose. Any product

Summary of Contents for Personal Fabricator




























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands