Version: 2.1
FB2300 Series User’s Quick Setting
Page 2/4
www.fabiatech.com
©2000-2005 FabiaTech Corporation
D. Keyboard and Mouse Connector (
CN11
,
J9
, and
JP6
)
CN11is a standard PS/2 type keyboard connector, so any PS/2 type keyboard can
plug into CN11 directly without extra adapter cable. J9 provides PS/2 mouse
interface and JP6 is use to enable or to disable it. Use the included mouse adapter
cable (optional) to connect between J9 and standard PS/2 mouse.
Note: In fact, CN11and J9 all support PS/2 keyboard and mouse signals and have
to order 3-head cable from your supplier.
E. LAN Connector (
CN7
: RJ45)
CN7 is a RJ45 connector with 2 LEDs. The left side LED (orange) indicates data is
accessing and the right side LED (green) is indicates power is OK and/or watchdog
status. (When watchdog is enabled, this LED will be blinking.) The following table
lists the pin assignment of CN7:
F. Floppy Connector (
CN2
: 34-pin 2.54mm IDC)
Note that the included floppy cable supports only 720KB, 1.44MB, and 2.88MB
floppy disk drives, not for 360KB and 1.2MB disk drives.
G. IDE Hard Disk Connector (
CN1
: 40-pin 2.54mm IDC)
Use the included hard disk cable, you can attach up to two 3.5” hard disk drives.
H. Parallel Port Connector (
CN3
: 26-pin 2.54mm IDC)
The included printer interface cable is used to transfer 26-pin connector into standard
DB25 connector.
I. Serial Port Connectors & Jumpers (
DB3
,
CN5
,
JP2
,
JP3
, &
J4
)
(1) RS-232 Pin Definitions (DB3 and CN5)
DB3 is standard DB9 serial port connector for serial port 1 (COM1) and CN5 is
10-pin 2.54mm IDC connector for serial port 2 (COM2). The included serial port
adapter cables are used to transfer CN5 connector into standard DB9 connector.
The following table shows the signal connections of DB3 (left) and the included
cable (right):
Signal
DB3
CN5
Signal (RS-232)
Signal (RS-485)
DB9
-DCD1
1 1 -DCD2
-
1
-DSR1
6 2 -DSR2
-
6
RXD1
2 3 RXD2
485- 2
-RTS1
7 4 -RTS2
-
7
TXD1 3
5
TXD2
485+
3
-CTS1
8 6 -CTS2
-
8
-DTR1
4 7 -DTR2
-
4
-RI1 9
8
-RI2
-
9
Ground
5 9 Ground
-
5
-
-
10
Case Ground
Case Ground
-
(2) RS-485 Jumper Select and Pin Definitions (JP3 & JP2)
Serial port 2 (COM2) provides RS-485 function by selecting JP3 jumper. When
RS-485 mode is selected, the RS-485 signals use the same connector as
RS-232. (Refer to last table please) JP2 is the terminator on/off jumper only when
using RS-485 mode. The following figure will guide you how to setup the RS-485
serial port.
(3) Extra RS-232 Header (J4: 3-pin 2.0mm JST)
Header J4 provides basic RS-232 signals of serial port 2. It is used to interface
with touch screen module or other internal connection usage.
1
8
CN7
(Front View)
CN7 Signal CN7
Signal
1 TPTX+ 5
Not
Used
2
TPTX -
6
TPRX -
3 TPRX+ 7 Not
Used
4 Not
Used 8 Not
Used
1
JP3
RS-232
Factory Preset
1
JP3
RS-485
1
JP2
1
JP2
Terminator On
Terminator Off
Factory Preset
3
1
J4
Pin 1: TXD2
Pin 2: RXD2
Pin 3: Ground
Pin 1: Mouse Data
Pin 2: Keyboard Data
Pin 3: Ground
Pin 4: VCC
Pin 5: Mouse Clock
Pin 6: Keyboard Clock
1
6
J9
1
JP6
1
JP6
Disable PS/2 Mouse
Enable PS/2 Mouse
Factory Preset
