Version: 2.1
FB2300 Series User’s Quick Setting
Page 4/4
www.fabiatech.com
©2000-2005 FabiaTech Corporation
6. Others (SSD and DOC Setting)
A. SSD and DOC Mapping Address Settings (
SW1-1
,
SW1-2
&
JP4
)
SW1-1 SW1-2
JP4
SSD Mapping
DOC Mapping
Remark
Off Off
Disable
C800:0
(8KBytes)
Disabled Preset
On Off
Disable
CC00:0
(8KBytes)
Disabled
Off On
Disable
D000:0
(8KBytes)
Disabled
On On
Disable
D800:0
(8KBytes)
Disabled
Off
Off
Enable
C800:0 (8KBytes)
CA00:0 (8KBytes)
On
Off
Enable CC00:0 (8KBytes)
CE00:0 (8KBytes)
Off
On
Enable
D000:0 (8KBytes)
D200:0 (8KBytes)
On
On
Enable
D800:0 (8KBytes)
DA00:0 (8KBytes)
Note: If DOC is enabled, please set JM4 as Flash setting and M4 (U5) is ready for
serving DiskOnChip.
B. SSD Memory Type Select (
SW1-4
and
JM1
to
JM4
)
JM1, JM2, JM3, and JM4 are use to select memory type of M1 (U21), M2 (U16), M3
(U10), and M4 (U5) respectively. When ROM memory is selected, SW1-4 is use to
select EPROM or Flash were installed.
SW1-4 Memory
Type
Remark
Off EPROM
Preset
On FLASH
Socket Package
ROM/RAM DiskOnChip Relative
Jumpers
U21 (M1)
DIP32
Yes
No
JM1
U16 (M2)
DIP32
Yes
No
JM2
U10 (M3)
DIP32
Yes
No
JM3
U5 (M4)
DIP32
Yes
Yes (If enabled)
JM4 & JP4
C. SSD Drive Select (
SW1-3
, Simulate as Floppy Disk Drive Only)
The SW1-3 switch will function only when the
SSD simulated as floppy disk drive
.
To simulate as hard disk drive or floppy disk drive is configurated by the BIOS setup
program. The default setting of SW1-3 is OFF.
(1) ROM (EPROM or Flash) or RAM Only (Installed start from M1)
(Note: EPROM and Flash can not exist simultaneously.)
SW1-3
ROM/RAM Disk (w/DOS)
ROM/RAM Disk (w/o DOS)
Off
Drive A: (Disk #0)
Drive B: (Disk #1)
On
Drive A: (Disk #0)
Disk #2
(2) ROM and SRAM Exist Simultaneously (ROM was installed start from M1)
SW1-3
ROM Disk (w/DOS)
ROM Disk (w/o DOS)
RAM Disk
Off
Drive A: (Disk #0)
Drive B: (Disk #1)
Disk #2
On
Drive A: (Disk #0)
Disk #2
Drive B: (Disk #1)
Note: The mapping disk drive of Disk #2 will always follow the exist
logical hard disk drives and simulated hard disk drives besides the
drive instaling DOS device driver after system is boot up.
D. SSD Simulates as Hard Disk Drive
Use the BIOS setup program to select hard disk drive or floppy disk drive to be
simulated. When SSD (ROM disk or RAM disk) simulates as hard disk drive, The
mapping disk drive of Disk #2 will always follow the exist logical hard disk drives and
simulated hard disk drives those which connect to the IDE connectors. The following
table issulates the drive mapping prioity of hard disk drives and folppy drives:
Mapping Prioity
Device Type
The First
IDE hard disk or DiskOnModule
The Second
On-Board
ROM
disk (Simulates as hard disk drive)
The Third
On-Board
RAM
disk (Simulates as hard disk drive)
The Fourth
On-Board DiskOnChip
The Fifth
Disk #2
The Sixth
Disk #3
The Last
Device Driver
Note:
The first mapping drive is drive C:.
6
JM1 to JM4
EPROM, Flash
DOC (M4 only)
Factory Preset
4
JM1 to JM4
SRAM
2
5
3
1
6
4
2
5
3
1
6
JP4
Disable DOC (M4 only)
Factory Preset
4
JP4
Enable DOC (M4 only)
2
5
3
1
6
4
2
5
3
1
