Faber MatriX 800/500 RD H, Installation Manual

Page: 13 / 36

Installation manual MatriX 800-1050x500 RD,ST H
12 < < < <

Open the glass clamps (see fig. 4.2);

Push up frame “C” and move slightly forward
so that it remains in the open position (see fig.
4.3).
See fig. 4.4:

Move the glass upwards so that the bottom
side is released from the groove.

Move the glass slightly to the left or right;

Pull out the glass and keep it in a safe place.
Replacing the glass is done in reverse order.
Adjusting front glass in relation to side glass;
If the front glass does not connect properly to
the side glass, adjusting screws to adjust the
glass (see fig. 4.5).

Please note!
Avoid fingerprints on the glass, these are no
longer removable once the fire is used.
5.2 MatriX 800-1050/500 ST

Remove cover strips “A” (fig. 4.6).

Open the glass clips (fig.4.7 )

Place the suction cups on the glass and
slide the upper frame “C” upward
(fig.4.8).
• See fig. 4.9:
1. Slide the glass to the top so that the
bottom is released from the slot.
2. Now carefully slide the glass to the
left or right.
3. Bring the released side towards you
and store the glass at a safe place.
For replacing the glass repeat the steps in reverse
order.

Please note!
Avoid fingerprints on the glass, these are no
longer removable once the fire is used.
6 Placing decoration material
It is not permitted to use other or to add more
Attention!
To decorate the burner it is necessary to remove
all windows from the fireplace, this is the only
way to get enough work space. See chapter 5
Scan the QR code for a clear video instruction on
decorating the burner.
Or see the included decoration
instruction card.
Chapter 17 provides an
overview of the complete log
setup.
To get the correct glow effect, the HPL module
must be switched on at 100% intensity.
Make sure the ITC-V2 app is connected to the fire.
See fig 1.9a.

enable the glow effect on the start screen
of the ITC-V2 APP. See fig 1.9b

click on the flame symbol in the circle, see
fig. 1.9b.

click on sprocket see fig. 1.9e.

set all settings to maximum, see fig. 1.9f.
Tip:
Regularly check the glow effect on the logs while
decorating.
It is not allowed to add other or more decoration
material in the combustion chamber.
6.1 Installing HPL light guiders
(800/500: 10 conductors / 1050/500: 12
conductors)
Place the light guiders in the slot opening of the
burner plate. See chapters 16.1 and 16.3
The light guider falls in a holder at the bottom of
the bottom.
When the light guider is correctly positioned, light
will shine from the front side of the glass, if this is
not the case, the light guider must be repositioned
(fig. 5.0).
With LED G6, a double light guide is placed in one
holder. (fig. 5.1)
Check whether all light guiders are in place.
(chapters 16.1 and 16.3)
6.2 Distribute glass of granulate and chips

Spread the glass granulate over the entire
bottom plate, with a slightly increasing thicker
layer towards the central burner.

Attention!

keep some glass granulate for later correction.

Divide the gray chips from the center over the
glass granulate. The precise arrangement of
black and gray chips can be divided at your
discretion.
Placing logs over the burner tubes:

Place log 1 over the central burner. Position
the log so that the ignition and ionization pin
are not obstructed by the log, keep checking
this while decorating.

Place wood logs 2 to 5 over the curved burner
tubes.