Faber CLAS30SSVA Installation Instructions Manual Download Page 5

Version 05/10- Page 5

TOOLS  NEEDED  FOR  INSTALLATION

• Saber Saw or Jig Saw
• Drill
• 1  1/4" Wood Drill Bit
• Pliers
• Phillips Screwdriver
• Flat Blade Screwdriver
• Wire Stripper or Utility Knife
• Metal Snips
• Measuring Tape or Ruler
• Level
• Pencil
• Caulking Gun
• Duct Tape

PARTS  SUPPLIED  FOR  INSTALLATION

• 1 Hardware Package
• 1 Literature Package

PARTS  NEEDED  FOR  INSTALLATION

• 2 Conduit Connectors
• Power Supply Cable
• 1 Wall or Roof Cap
• All Metal Ductwork

9 Feet Straight Duct

2 - 90˚ Elbows

Wall Cap

Total System

9.0 feet

10.0 feet

0.0 feet

19.0 feet

FIGURE  3

3.0 feet

5.0 feet

12.0 feet

0.0 feet

45˚ Elbow

90˚ Elbow

90˚ Flat Elbow

Wall Cap

FIGURE  2

CALCULATE  THE  DUCTRUN  LENGTH

The ductrun should not exceed 35 equivalent feet 
if ducted with the required minimum of 6" round 
ductwork.  Calculate the length of the ductwork 
by adding the equivalent feet in 

FIGURE 2

 for 

each piece of duct in the system  An example 
is given in 

FIGURE 3

.

For best results, use no more than three 90°  
elbows.  Make sure that there is a minimum of 
24" of straight duct between elbows if more 
than one is used.  Do not install two elbows 
together.  If you must elbow right away, do it 
as far away from the hood's exhaust opening 
as possible.

   WARNING

Because of the weight and size of the 
rangehood canopy, two or more people 
are needed to move and safely install the 
rangehood canopy.

Failure to properly lift rangehood could 
result in damage to the product or personal 
injury.

PERSONAL INJURY HAZARD

PLAN  THE  INSTALLATION

This rangehood can be installed as either ducted or ductless.  In a ducted 
application, this rangehood can be vented through the wall or ceiling.  To vent 
through a wall, a 90° elbow is used.  When installed ductless, the rangehood 
vents out of the grates on the sides of the lower chimney.  Ductless installations 
require a 

Ductless Conversion Kit

, available from your dealer.

WARNING!

  BEFORE MAKING ANY CUTS OR HOLES FOR INSTALLATION, 

DETERMINE WHICH VENTING METHOD WILL BE USED AND CAREFULLY 
CALCULATE ALL MEASUREMENTS.

RANGEHOOD  COMPONENTS

!

FIGURE  1

A. CANOPY SECTION
B. LOWER CHIMNEY COVER
C. UPPER CHIMNEY COVER
D. MOUNTING SCREWS
E. CHIMNEY MOUNTING BRACKETS
F. CHIMNEY SCREWS
G. DAMPER

E

G

CAUTION

To reduce risk of fire and to properly exhaust 
air, be sure to duct the air outside – Do not vent 
exhaust air into spaces within walls or ceilings 
or into attics, crawl spaces, or garages.

A

C

F

B

D

Summary of Contents for CLAS30SSVA

















Reviews: