FAAC XR4 433 C, Manual

Page: 6 / 20

2
ENGLISH
3 MEMORY STORAGE OF RADIO CONTROLS
At the most two types of radio coding (DS, SLH,
LC) can simultaneously coexist on the XR C board;
the first coding (e.g. SLH) on channels 1 and 2,
the second (e.g DS) on channels 3 and 4.
3.1 MEMORY STORAGE OF DS REMOTE CONTROLS
3.2 MEMORY STORAGE OF SLH REMOTE CONTROLS
A maximum of 250 codes for channels 1-2 and
250 codes for channels 3-4 can be memory
stored.
1) On the DS radio control, select the required ON-OFF
combination for the 12 dip switches.
2) Press for 1 second, the push-button on the receiver (Fig.1
ref.
6
) relating to the channel you wish to associate with
the radio control
3) The relevant LED on the receiver (Fig. 1 ref.
5
) begins
to flash slowly for 5 secs.
4) Within these 5 secs., press the appropriate push-button
on the radio control.
5) The relevant LED (Fig.1 ref. 5 ) lights up on steady beam
for 1 second and then goes OFF, indicating that storage
was executed.
The board will send a command to the output
associated with the channel.
6) To add other radio controls, set the same ON - OFF
combination used in point 1).
1) On the SLH master radio control, simultaneously press
and hold down push-buttons P1 and P2.
2) The radio control LED begins to flash (for about 10
secs.).
3) Release both push-buttons.
4) Press, for 1 second, the push-button on the receiver
(Fig.1 ref.
6 ) relating to the channel you wish to associate
with the radio control.
5) The relevant LED on the receiver (Fig. 1 ref.
5 ) begins
to flash slowly for 5 secs.
6) Within these 5 secs., while the radio control LED is still
flashing, press and hold down the required push-button
on the radio control (the radio control LED lights up on
steady beam).
7) The LED on the board (Fig.1 ref.
5
) lights up on steady
beam for 1 second and then goes OFF, indicating that
storage was executed.
8) Release the radio control push-button.
9) Quickly press twice in succession the memory stored
radio control push-button.
The board will send a command to the output
associated with the channel.
10) To add other radio controls, transfer the code of the
memory-stored push-button of the radio control to the
relevant push-button of the radio controls to be added,
observing the following procedure:
a) On the memory stored radio control, simultaneously
press and hold down push-buttons P1 and P2.
b) The radio control LED begins to flash.
c) Release both push-buttons.
d) Press the memory stored push-button and hold it down
(the radio control LED lights up on steady beam).
e) Bring the radio controls near, press and hold down the
push-button of the radio control to be added, releasing
it only after the double flash of the radio control LED, which
indicates learning was executed.
- Quickly press twice the push-button of the new memory
stored radio control.
The board will send a command to the output
associated with the channel.
3.3 MEMORY STORAGE OF LC REMOTE CONTROLS
1) Press, for 1 second, the push-button on the receiver (Fig.1
ref. 6 ) relating to the channel you wish to associate
with the radio control.
2) The relevant LED on the receiver (Fig. 1 ref. 5 ) begins
to flash slowly for 5 secs.
3) Within these 5 secs., press the appropriate push-button
on the LC remote control.
4) The LED on the receiver (Fig.1 ref. 5 ) lights up on steady
beam for 1 second, indicating memory storage was
executed, and then resumes flashing for another 5
secs., during which another radio control can be
memory stored.
5) When the 5 secs. have elapsed, the LED goes OFF
indicating the end of the procedure.
6) To memory store other radio controls, repeat the
previous procedure.
If you wish to proceed in remote mode, (without opening
the receiver container), follow the procedure below:
a) Take an already memory stored radio control.
b) Press and simultaneously hold down push-buttons P1
and P2 until the flashing light of the LED (Fig.1 ref.
5
) on
the receiver board lights up.
c) The LED will flash slowly for 5 secs.
d) Within 5 secs. press the push-button of the radio control
that had been memory stored to enable learning on
the selected channel.
e) The LED on the board relating to the channel being
learned flashes for 5 secs., within which time the code
of another radio control must be transmitted.
f) The LED (Fig.1 ref. 5 ) lights up on steady beam for 2
seconds, indicating memory storage was executed,
and then resumes flashing for 5 secs., during which point
“e” can be repeated, and also the subsequent points,
for other remote controls and finally goes OFF.
The LC radio coding is available only for certain
markets and only for receiver XR433C.
1) To delete ALL the radio control codes associated with
channels 1-2 or 3-4 , hold down the relevant push-button
(Fig.1 ref. 6 ) for 10 seconds.
( e.g. TO DELETE ALL RADIO CONTROLS ASSOCIATED
WITH CHANNELS 1-2, PRESS SW1 OR SW2).
4 DELETION OF ALL RADIO CONTROLS
ASSOCIATED WITH CHANNELS 1-2 OR 3-4
This operation is NOT reversible and, if the
radio controls associated with channels 3-4
are deleted, it also entails the deletion of
activation timer of output 4.
To change over from one code to another, you
must delete the existing one (see paragraph
on deletion), and repeat the memory-storage
procedure.