8
455 D Control Board
F
+
+
To access ADVANCED PROGRAMMING, press and hold
key F and then press key +:
•
Release key +, the unit displays the name of the first function.
•
Release key F, modify the value of the function with keys
+ and -.
•
Press and hold key F, the unit displays the name of the next
function, and if you release it, the value that can be modified
with keys + and -.
•
When you reach the last function, press F to exit the program,
the unit resumes monitoring input status.
The following table shows the sequence of functions
accessible in ADVANCED PROGRAMMING:
ADVANCED PROGRAMMING
MAXIMUM TORQUE AT INITIAL THRUST:
The motors operate at maximum torque (ignoring
the torque setting) at start of movement. Useful
for heavy leaves.
= Active
= Disabled
LAST STROKE AT CLOSING:
The motors are activated at full speed for 1
second to facilitate locking of the electric lock.
= Active
=Disabled
REVERSING STROKE:
Before opening, while the gate is closed, the
motors thrust to close for 2 seconds thus
facilitating release of the electric lock.
= Active
= Disabled
LEAF 2 OPENING DELAY (2 s):
Enables delayed start (at opening) of leaf 2,
avoiding interference between leaves.
= Active
= Disabled
FAIL SAFE:
If this function is activated, it enables a function
test of the photocells before any gate movement.
If the test fails (photocells not serviceable), the
gate does not start the movement.
= Active
= Disabled
PRE-FLASHING (5 s):
Activates the flashing lamp for 5 seconds before
start of movement.
= Active
= Disabled
ELECTRIC LOCK ON LEAF 2:
For using the electric lock on leaf 2 instead of
on leaf 1.
= Active
= Disabled
INDICATOR-LIGHT:
If
is selected, the output functions as a
standard indicator-light (lighted at opening and
pause, flashing at closing, and off when gate is
closed). Different figures correspond to the extra
time compared to normal work time (opening or
closing) when the output can be used - via a relay
- to power a courtesy light. Time can be adjusted
from to
sec. in 1 sec. steps, and from
to
min. in 10 sec. steps.
= Standard indicator-light
from to
= Timed output
CLOSING PHOTOCELLS REVERSE AT
RELEASE:
Enable this function if you want the closing
photocells to stop movement and reverse at
release. Default setting is immediate reverse.
= Active
= Disabled
ASSISTANCE REQUEST (combined with
next function):
If activated, at the end of countdown (settable
with the next function i.e. “Cycle programming”)
it affects 8 s of pre-flashing at every Open pulse
(job request). Can be useful for setting scheduled
maintenance jobs.
= Active
= Disabled
CYCLE PROGRAMMING:
For setting countdown of system operation
cycles. Settable (in thousands) from to
thousand cycles. The displayed value is updated
as cycles proceed.
This function can be used to check use of the
board or to exploit the “Assistance request”.
A.D.M.A.P. FUNCTION:
When enabled, the safety devices operate in
compliance with French standard NFP 25/362.
= Active
= Disabled
Exit from programming and return to inputs
status monitoring.
NB:
Parameter modifications take effect immediately. Exit
out of programming to save changes. If the equipment is
powered down before returning to normal status monitoring,
any unsaved modifications will be lost.
To restore programming defaults, press and hold the
three b, -, F simultaneously for 5 seconds.
ANTI-CRUSHING SENSITIVITY:
When operating with the gatecoder, it controls
anti-crushing sensitivity.
= Low
= High.
EXTRA WORK TIME:
When operating without a gatecoder and limit-
switch, if reversing occurs, and if the leaf does
not reach its end contact point, you can activate
this function to increase work time.
= Active
= Disabled
Display
Function
Default
1.5.2 Advanced Programming
Display
Function
Default
(800) 878-7829
www.FastGateOpeners.com
