F.F. Group DSL 750 PLUS, Instructions Manual

Page: 9 / 60

DSL 750 PLUS English | 9
www.ffgroup-tools.com
SAFETY INSTRUCTIONS FOR DRYWALL
SANDERS
SAFETY WARNINGS COMMON FOR SANDING OP-
ERATIONS
f
This power tool is intended to function as a sander.
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
f
This power tool is not recommended for grinding,
wire brushing, polishing or cutting off operations.
Operations for which the power tool was not de -
signed may create a hazard and cause personal
injury.
f
Do not use accessories which are not specifically
designed and recommended by the tool manufac -
turer. Just because the accessory can be attached
to your power tool, it does not assure safe opera -
tion.
f
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can fly apart.
f
The outside diameter and the thickness of your ac-
cessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
f
Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted
by flanges, the arbour hole of the accessory must
fit the locating diameter of the flange. Accessories
that do not match the mounting hardware of the
power tool will run out of balance, vibrate exces -
sively and may cause loss of control.
f
Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pads for cracks, tear or
excess wear, wire brushes for loose or cracked
wires. If the power tool or accessory is dropped,
inspect for damage or install an undamaged acces -
sory. After inspecting and installing an accessory,
position yourself and bystanders away from the
plane of the rotating accessory and run the pow -
er tool at maximum no load speed for one minute.
Damaged accessories will normally break apart
during this test time.
f
Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and shop apron capa -
ble of stopping small abrasive or workpiece frag-
ments. The eye protection must be capable of
stopping flying debris generated by various opera-
tions. The dust mask or respirator must be capable
of filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may
cause hearing loss.
f
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of the
workpiece or of a broken accessory may fly away
and cause injury beyond the immediate area of
operation.
f
Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. A cutting accessory contacting a "live"
wire may make exposed metal parts of the power
tool "live" and could give the operator an electric
shock.
f
Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spin -
ning accessory.
f
Never lay the power tool down until the accessory
has come to a complete stop. The spinning acces -
sory may grab the surface and pull the power tool
out of your control.
f
Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accesso -
ry could snag your clothing, pulling the accessory
into your body.
f
Regularly clean the power tool’s air vents. The mo-
tor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may
cause electrical hazards.
f
Do not operate the power tool near flammable ma-
terials. Sparks could ignite these materials.
f
Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
ƒ
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in
turn causes the uncontrolled power tool to be
forced in the direction opposite of the accesso -
ry’s rotation at the point of the binding.
ƒ
Kickback is the result of power tool misuse and/
or incorrect operating procedures or conditions
and can be avoided by taking proper precautions
as given below
f
Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up. The operator can control torque
reactions or kickback forces, if proper precautions
are taken.
f
Never place your hand near the rotating accessory.
The accessory may kickback over your hand.
f
Do not position your body in the area where power
tool will move if kickback occurs. Kickback will pro-
pel the tool in the direction opposite to the wheel’s
movement at the point of snagging.
f
Use special care when working corners, sharp edg-
es etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency
to snag the rotating accessory and cause loss of
control or kickback.
SAFETY WARNINGS SPECIFIC FOR SANDING OP-
ERATIONS
f
When sanding, do not use excessively oversized
sanding disc paper. Follow the manufacturers’
recommendations when selecting sanding paper.
Larger sanding paper extending beyond the sand -