F.F. Group DSL 750 PLUS, Instructions Manual

Page: 10 / 60

DSL 750 PLUS | English 10
ing pad presents a laceration hazard and may cause
snagging, tearing of the disc, or kickback.
GENERAL
ƒ
This tool should not be used by people under the
age of 16 years.
ƒ
This tool is not intended for use by children and
persons with reduced physical, sensory or men -
tal capabilities, or lack of experience and knowl-
edge.
ƒ
Ensure that children do not play with the tool.
ƒ
This tool is not suitable for wet sanding.
ƒ
Always disconnect plug from power source be -
fore making any adjustment or changing any ac-
cessory.
ACCESSORIES
ƒ
FF GROUP can assure flawless functioning of the
tool only when the correct accessories are used
which can be obtained from your FF GROUP deal-
er.
ƒ
For mounting/using non-FF GROUP accessories
observe the instructions of the manufacturer
concerned.
ƒ
Handle and store accessories with care.
OUTDOOR USE
ƒ
Connect the tool via a fault current (FI) circuit
breaker with a triggering current of 30 mA max-
imum.
BEFORE USE
ƒ
Before using the tool for the first time, it is rec-
ommended to receive practical information.
ƒ
Always check that the supply voltage is the same
as the voltage indicated on the nameplate of the
tool (tools with a rating of 230V or 240V can also
be connected to a 220V supply).
ƒ
Use suitable detectors to find hidden utility lines
or call the local utility company for assistance
(contact with electric lines can lead to fire or
electrical shock; damaging a gas line can result in
an explosion; penetrating a water pipe will cause
property damage or an electrical shock).
ƒ
Do not work materials containing asbestos (as-
bestos is considered carcinogenic).
ƒ
Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful (contact with or inhalation of the dust
may cause allergic reactions and/or respiratory
diseases to the operator or bystanders); wear a
dust mask and work with a dust extraction device
when connectable.
ƒ
Certain kinds of dust are classified as carcinogen-
ic (such as oak and beech dust) especially in con-
junction with additives for wood conditioning;
wear a dust mask and work with a dust extraction
device when connectable.
ƒ
Follow the dust-related national requirements
for the materials you want to work with.
ƒ
Do not clamp the tool in a vice.
ƒ
Use completely unrolled and safe extension
cords.
DURING USE
ƒ
Do not touch the moving sanding disc.
ƒ
Do not continue to use worn, torn or heavily
clogged sanding discs.
ƒ
If the cord is damaged or cut through while work-
ing, do not touch the cord, but immediately dis -
connect the plug.
ƒ
Never use the tool when cord is damaged; have it
replaced by a qualified person.
ƒ
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect
the plug.
ƒ
In case of current interruption or when the plug is
accidentally pulled out, unlock the on/off switch
immediately in order to prevent uncontrolled re -
starting.
AFTER USE
ƒ
After switching off the tool, never stop the ro-
tation of the accessory by a lateral force applied
against it.
GUIDELINES FOR USING EXTENSION CORDS
f
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and over -
heating.
f
Always replace a damaged extension cord or have
it repaired by a qualified person before using it.
f
Protect your extension cords from sharp objects,
excessive heat and damp/wet areas.
f
Use a separate electrical circuit for your tools. This
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor
to the power line, make sure the switch is in the
OFF position and the electric voltage is rated the
same as the voltage stamped on the motor name -
plate. Running at a lower voltage will damage the
motor.
PRODUCT SPECIFICATIONS
INTENDED USE
This tool is intended for dry sanding of plastered
walls and ceilings; it is particularly suitable for re-
moving paint coatings, adhesives and loose plaster.
Only use the tool when correctly and completely
assembled (be aware that FF GROUP cannot be
hold responsible for tool damage and/or personal
injuries resulting from the incorrect assembly of
the tool). Read this instruction manual carefully
before use and save it for future reference .
TECHNICAL DATA
Article Number 43 282
Model DSL 750 PLUS
Rated voltage V 230-240
Frequency Hz 50