F.F. Group AG 230/2600S HD, Original Instructions Manual

Page: 9 / 52

GUIDELINES FOR USING EXTENSION CORDS
f
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
f
Always replace a damaged extension cord or have it
repaired by a qualified person before using it.
f
Protect your extension cords from sharp objects,
excessive heat and damp/wet areas.
f
Use a separate electrical circuit for your tools. This
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF
position and the electric voltage is rated the same
as the voltage stamped on the motor nameplate.
Running at a lower voltage will damage the motor.
PRODUCT SPECIFICATIONS
INTENDED USE
The machine is intended for cutting, roughing and
brushing of metal and stone materials without the
use of water.
TECHNICAL DATA
Article number 45 591
Model AG 230/2600S HD
Rated voltage
V 220-240
hz 50
Rated power input W 2.600
Rated speed min
-1
6.600
Grinding disc diameter,
max.
mm 230
Thread of grinder spindle M 14
Thread length (max.) of
grinder spindle
mm 84,5
Weight (net) kg 6,58
Sound emission values determined according
to EN 60745-1
Typically the A-weighted noise levels of the product
are:
Sound pressure level
dB(A) 95,6
Sound power level dB(A) 106,6
Uncertainty K dB 3
Vibration total values a
h
(triax vector sum)
and uncertainty k determined according to
EN 60745-1
Vibration level max:
a
h,AG
m/s 2 6,186
K m/s
2
1,5
NOISE/VIbRATION INFORmATION
The vibration level given in this information sheet
has been measured in accordance with a stan-
dardized test given in EN 60745 and may be used
to compare one tool with another. It may be used
for a preliminary assessment of exposure. The
declared vibration emission level represents the
main applications of the tool. however if the tool
is used for different applications, with different
accessories or insertion tools or is poorly main-
tained, the vibration emission may differ. This
may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibra-
tion should also take into account the times when
the tool is switched off or when it is running but
not actually doing the job. This may significantly
reduce the exposure level over the total working
period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organization of work patterns.
IDENTIFICATION
1. On/Off switch
1a. Safety lock-out
2. Spindle lock button
3. Auxiliary handle
4. Protective guard
5. Release lever for protection guard
6. Spindle
7. Clamping flange
8. Spanner
9. Mounting flange
USE
mOUNTING OF ACCESSORIES (E)
f
Clean spindle (06) and all parts to be mounted.
f
Tighten clamping flange (07) with spanner (08)
while pushing spindle-lock button (02) .
f
For removing accessories handle vice-versa.
mOUNTING OF AUxILIARy hANDLE (D)
Screw auxiliary handle (03) on the right, the top,
or the left of the tool (depending on the work to
be carried out).
REmOVING / mOUNTING / ADjUSTING OF pRO-
TECTIVE GUARD (C)
f
Place protective guard (04) on the spindle collar of
the tool head and turn it to the required position
(depending on the work to be carried out).
f
If necessary, adjust protective guard (04) by tighten-
ing screw which is pre-set at manufacturing.
BEFORE USING THE TOOL
f
Ensure that accessory is correctly mounted and firm -
ly tightened.
f
Check if accessory runs freely by turning it by hand.
f
Test-run tool for at least 60 seconds at highest no-
load speed in a safe position.
f
Stop immediately in case of considerable vibration
or other defects and check tool to determine the
cause.
SwITChING ON AND OFF (Β)
f
Switching on the device:
English | 9
www.ffgroup-tools.com
AG 230/2600S HD