Ezze Mobile Tech SL599 Technical Manual Download

Page: 63 / 116

ODEL

SL599 V

ERSION

V_1.0

REPARED BY

H/W

ATE

2007.04.11

UBJECT

ECHNICAL

ANUAL

AGE

41/52

SL599

ECHNICAL

ANUAL

10.

Vibrator , Alerter, LED switches

Three built-in open-drain output switches drive the vibrator motor(Pin38), alerter beeper(Pin39) and

LED(Pin41) in the handset. Each switch is controlled by baseband chipset with enable pins. The

switch of LED can sink 150mA to drive up to 10 LED simultaneously for backlight. The switch of

vibrator can sink 250mA for a vibrator motor. The switch of alerter can sink 300mA to drive the

beeper. And all the open-drain output switches are high impedance when disable. ALERTER pin is

dedicated to Main KEY Back-Light LED, VIBRATOR pin is dedicated to Vibrator Motor.

11.

Battery Charger

BATUSE pin can set MT6305 to fit the battery type. When BATUSE is set low, Li-ion battery is used.

MT6305 charges the battery in three phases : pre-charging, constant current mode charging, and

constant voltage mode charging. The circuitry of MT6305 combines with a PMOS transistor, diode,

current-sense resistor externally to form a simple and low cost linear charger. MT6305 is available

pulsed top-off charging algorithm by the CHRCNTL pin control from baseband chipset.

Figure 27. Charger and Voltage Detection

Figure 28. Li-Ion Battery Charging Profile.

Summary of Contents for SL599





















































































































Search results

Summary of Contents for SL599

Reviews:

Related manuals for SL599

Brands by name

Popular brands

Ezze Mobile Tech SL599, Technical Manual

Search results

Summary of Contents for SL599

Reviews:

Related manuals for SL599

Brands by name

Popular brands