background image

5

3�  Change Language

When device charging, press and hold the Mode Button for 3 seconds to enter language changing mode 

(Language order: English, French, German, Italian ). Please press Mode Button to change to a different 

language and press and hold the Mode Button for 3 seconds to exit.

The default language is English.

Mode Button

4�  Add Clean Water

Take off the clean water bucket and open the bucket cover, and then add clean water and half a bottle 

cap of cleaning solution (about 3.5ml), and close the bucket cover and then install the bucket back to the 

device.

The water temperature should be lower than 60°C (140°F). 

1. Take off the clean water bucket and fill it up with 

clean water and half a bottle cap of cleaning solution 

(about 3.5ml).

2. Install the bucket back to the device, you can 

hear 'click' sound. Make sure the cover is tight.

5�  Start Cleaning

Take the device off from the charging base and gently step on the brush heads after placing it on the ground, 

and then tilt the device backward; press the Power Button for about 3s to start the device.

The default working mode is Auto Mode. Press the Power Button to stop working.

Please do not clean alcohol, foam liquid and etc. with the device.

WARNING:

• 

Do not use on foam liquid. Power Mode is recommended to be used in 

heavily soiled environments.

•  This appliance comes with a vertical switch. When working, please lean 

it before you use it. The tilt angle cannot exceed 140 degrees in case of 

water leaking.

Summary of Contents for RH1















Reviews: