background image

7

8�  Pour Dirty Water

Take off the dirty water bucket and open the bucket cover to take out of the dirt separator within the bucket, and 

then pour down the dirty water and clean the dirty marks, and finally install the dirty bucket back into the device.

•  If HEPA is required to be washed, please install and use it after wash and dry it, otherwise the device 

performance will be affected.

•  Always hold the bucket. If you hold the cover, the bucket body may drop.

1. Take out dirty water bucket.

2. Hold the bucket and take out the 

cover.

3. Take out the dirt 

separator.

4. Clean the cover, the dirt separator 

and the bucket.

5. Put them back and install the bucket 

back to the device, you can hear 'click' 

sound.

9�  Rolling Brush Air Dry Introduction

• 

When charging, rolling brush air dry mode is automatically on.

•  To make sure the rolling brush is air-dried more evenly and thoroughly, the rolling brush rolls every 3 

minutes during this progress.

• 

This mode will run continuously for about 2 hours.

Rolling Brush Air Dry

Mode Button

Product Disassembly

1�  Disassembly of Handle

a. 

Use tools, such as tweezers, to strip the soft robber on the back of the device. 

b. 

Find another slender tool, such as a hex screwdriver, to press it into the hole, and pull the handle up 

in the meantime.

Summary of Contents for RH1















Reviews: