Ezee-On 4600 DISC, Owner'S Manual, Page: 32 / 78

Page 31
ASSEMBLY INSTRUCTIONS CONTINUED:
g) See Fig. 28. Install one (1) 1/4" x 54" (6.35 mm x 1372 mm) hydraulic hose, to the shaft end port of the L.H. 5" x 36" (127 mm x 914 mm) wing lift
cylinder, and fasten opposite end to one (1) 3/8" x 3/8" x 3/8" (9.39 mm x 9.39 mm x 9.39 mm) tee. Fasten one (1) 1/4" x 54" (6.35 mm x 1372 mm)
hydraulic hose, to the shaft end port of the R.H. 5" x 36" (127 mm x 914 mm) wing lift cylinder, and fasten opposite end to 3/8" x 3/8" x 3/8" (9.39
mm x 9.39 mm x 9.39 mm) tee.
h) See Fig. 28. Install one (1) 3/8" x 24" (9.39 mm x 610 mm) hydraulic hose, to the barrel end port of the L.H. 5" x 36" (127 mm x 914 mm) wing lift
cylinder and fasten opposite end to the barrel end port of the R.H. 5" x 36" (127 mm x 914 mm) wing lift cylinder.
i) See Fig. 28. Install one (1) 3/8" (9.39 mm) male x 3/8" (9.39 mm) female swivel adapter, in to the L.H. lockup valve. Fasten one (1) 3/8" x 100"
(9.39 mm x 2540 mm) hydraulic hose, in 3/8" (9.39 mm) tee, arrow 23. Fasten opposite end of same hose to the 3/8" (9.39 mm) male x 3/8" (9.39
mm) female swivel adaptor in lockup valve.
j) See Fig. 28. Install two (2) 3/8" x 172" (9.39 mm x 4369 mm) hydraulic hoses to the front port of hydraulic lockup valves, and run hoses to front of
hitch.
k) See Fig. 28. Install one (1) 3/8" x 287" (9.39 mm x 7290 mm) hydraulic hose, from the 3/8" (9.39 mm) tee, to front of disc.
27. ATTACHING HYDRAULIC HOSES TO ROCKSHAFT CYLINDERS AND WING CYLINDERS - WIDE WING FRAME ONLY - See Fig. 30.
(See Specifications on page 5 to determine wing width for your machine).
IMPORTANT: DO NOT USE TEFLON TAPE TO SEAL HYDRAULIC HOSES AND FITTINGS. IF PIECES OF TAPE GENT INTO THE HYDRAULIC SYSTEM
THEY MAYPLUG SMALL ORIFICES.
NOTE: To determine if your machine has a wide wing frame. See Specification Chart on Page 5.
NOTE: To ensure that the hydraulic system does not leak, seal fittings and hoses with sealing liquid.
a) See Fig. 30. Install one (1) 1/2" x 90 degree (12.7 mm) swivel street elbow, into the shaft end port of the R.H. 3" x 24" (76.2 mm x 610 mm) wing
rockshaft cylinder. Connect one (1) 3/8" x 489" (9.39 mm x 12421 mm) hydraulic hose to 1/2" x 90 degree (12.7 mm) swivel street elbow. Then run
the hose across the wing frame to the centre of the main frame, and to front of hitch.
b) See Fig. 30. Install one (1) 1/2" x 90 degree (12.7 mm) swivel street elbow, in shaft end, port of 3-1/2" x 24" (88.9 mm x 610 mm) L.H. wing
rockshaft cylinder. Install one (1) 1/2" x 90 degree (12.7 mm) swivel street elbow, in the barrel end port of the R.H. 3" x 24" (76.2 mm x 610 mm)
wing rockshaft cylinder. Connect one (1) 3/8" x 402" (9.39 mm x 10211 mm) hydraulic hose, to 1/2" x 90 (12.7 mm) degree swivel elbow, on R.H.
cylinder. Next run the hose across frame to 1/2" x 90 degree (12.7 mm) swivel elbow, on L.H. cylinder.
c) See Fig. 30. Install one (1) 1/2" x 90 degree (12.7 mm) swivel street elbow, to barrel end port of L.H. 3-1/2" x 24" (88.9 mm x 610 mm) wing rockshaft
cylinder. Install one (1) 1/2" x 90 degree (12.7 mm) swivel street elbow, to shaft end port of 4" x 24" (101.6 mm x 610 mm) main frame rockshaft
cylinder. Connect one (1) 3/8" x 253" (9.39 mm x 6426 mm) hydraulic hose, to 1/2" x 90 degree (12.7 mm) swivel elbow, on main frame rockshaft
cylinder. Next run the hose across frame to 1/2" x 90 degree (12.7 mm) swivel elbow on L.H. 3-1/2" x 24" (88.9 mm x 610 mm) wing rockshaft
cylinder.
d) See Fig. 30. Install one (1) 1/2" x 90 degree (12.7 mm) swivel street elbow, into the barrel end port of 4" x 24" (101.6 mm x 610 mm) main frame
rockshaft cylinder. Connect one (1) 3/8" x 24" (9.39 mm x 610 mm) hydraulic hose, to rear port of R.H. lock-up valve, with one (1) 3/8" (9.39 mm)
male-female swivel. Next connect same hose to 1/2" x 90 degree (12.7 mm) swivel elbow, on front port of main frame cylinder.
e) See Fig. 30. Install one (1) 3/8" (9.39 mm) male x 3/8" (9.39 mm) male union, in the barrel end port of the rear L.H. 5" x 36" (127 mm x 914 mm)
wing lift cylinder. Then install one (1) 3/8" x 3/8" x 3/8" (9.39 mm x 9.39 mm x 9.39 mm) tee, to the 3/8" (9.39 mm) union. Install one (1) 3/8" x
90 degree (12.7 mm) street elbow, into the shaft end of L.H. 5" x 36" (127 mm x 914 mm) wing lift cylinder.
f) See Fig. 30. Install one (1) 3/8" x 90 degree (9.39 mm) swivel street elbow, into the barrel end port of the rear R.H. 5" x 36" (127 mm x 914 mm) wing
lift cylinder. Install one (1) 3/8" x 90 degree (12.7 mm) street elbow, into the shaft end port, of rear R.H. 5" x 36" (127 mm x 914 mm) wing lift
cylinder.
g) See Fig. 30. Install one (1) 3/8" (9.39 mm) male union into one (1) 3/8" (9.39 mm) steel cross, and fasten into the rear port of the L.H. lockup valve.
Then fasten one (1) 3/8" (9.39 mm) male-female swivel into the 3/8" (9.39 mm) steel cross. Fasten one (1) 3/8" x 106" (9.39 mm x 2692 mm)
hydraulic hose to the 3/8" (9.39 mm) tee on the barrel end of the rear L.H. wing lift cylinder. Fasten opposite end of same hose to the 3/8" (9.39 mm)
male-female adapter. Run this hose through the lower R.H. hole in the front wing lift cylinder lug.
h) See Fig. 30. Install one (1) 3/8" x 90 degree (9.39 mm) swivel street elbow into the barrel end of the front L.H. 5" x 36" (127 mm x 914 mm) wing
lift cylinder. Install one (1) 3/8" x 90 degree (9.39 mm) swivel street elbow into the shaft end of the front L.H. 5" x 36" (127 mm x 914 mm) wing lift
cylinder.