background image

- 43 -

Clean the chamber interior as appropriate 
with removing bracket holder, brackets, 
shelves, and  bottom plate. 

Wipe with soft wring-up wet cloth.
To remove greasy dirt, use some neutral 
detergent, if needed. And clean off the 
detergent with a cloth.

To remove the bracket holder, loosen both 
top and bottom screw of holder and slide 
the holder upward. Repeat the same step 
for other three holder.

You will find a strainer for drain port at the 
bottom of chamber, after the bottom plate 
of chamber is taken out.
Clean the strainer.

Bracket  holder

Screw

Fixing block of 
bracket holder. 
(attached to the 
chamber wall)

Down-turned 
hook (attached 
to the bracket 
holder)

Screw

Bracket

Bracket holder

*** Antibacterial silver stainless steel ***
In this unit antibacterial silver stainless 
steel is used as the material of interior.
Antibacterial silver stainless steel has high 
antibacterial spectrum at 99% or more in 
multiple screening test of antibacterial 
effective (Film coherent method).
The effect is also shown in our sampling 
test of chamber air to be beneficial for 
antibacterial ability.

Bracket holder, brackets and a part of 
chamber interior is not made of 
antibacterial silver stainless steel.

2. Cleaning the chamber

3. Cleaning of refrigeration unit filter

The operation with the clogged filter 
worsens the cooling performance.
Also, some troubles are caused on the 
refrigeration unit.
Clean the filter on a regular schedule 
depending on environmental or operating 
condition.

The filter is attached at inside of the 
ventilation port.
Hold the left edge of the ventilation cover 
with your hand, and pull it open.

(1)

Shelf

Strainer for 
drain port

Open

Ventilation cover

Ventilation grill

Bottom plate
* The thicker side is 

set at front side of 
chamber.

Summary of Contents for KCL-2000W



















































Reviews:

Related manuals for KCL-2000W