1
IMPO
RTAN
T:
IMPO
RTAN
T:
Go to
www.
extron.com f
or the complete
produ
ct specifications
.
PMK 560 • Installation Guide
The Extron PMK 560 Pole Mount Kit, designed for use with the Extron PoleVault™ System, allows for easy mounting of PoleVault
products to a projector pole. It is used to mount the PoleVault system switcher, the associated power supply, and an accessory
device within an enclosure and below a suspended ceiling.
CAUTION:
The maximum load for the PMK 560 is 15 lbs (6.8 kg).
ATTENTION :
La charge maximum pour le PMK 560 est 6,8 kg (15 lbs).
Items included in the kit are:
•
Covers (2)
•
Base plate (1)
•
Mounting plate (1)
•
Tie wraps and pads (to secure power supply)
•
4-40 Screws (to mount devices) (3)
•
Cover Screws (4)
NOTE:
For full device installation, configuration, menus,
connector wiring, and operation details of the PoleVault
switcher, see the
PoleVault System Installation Guide
,
available at
.
Installation
To install the PMK 560 in a PoleVault system:
1.
Remove the four cover screws from the center of the PMK 560
(see figure 1). Slide the two halves apart and remove them from
the base plate.
NOTE:
If the PoleVault switcher and its power supply are
already installed, go directly to step 4.
2.
To mount the PoleVault switcher, place the mounting plate,
with the raised tabs upwards, on the top surface of the
switcher and pass the two supplied 4-40 x 3/16 inch screws
into the top of the switcher (see figure 2,
1
). Secure the
mounting plate but do not overtighten.
ATTENTION:
•
Use only supplied screws to avoid damaging the
switcher.
•
Utilisez seulement les vis fournies pour ne pas
endommager le sélecteur.
3.
Attach the associated power supply to the base plate with the
supplied tie wraps and pads, by passing them through the
appropriate slots and around the power supply (
2
).
Tighten until snug.
4.
Loosen the four pipe collar set screws (
3
), and slide
the base plate up the pipe until it is touching the suspended
ceiling.
5.
Level the base plate and secure it by fully tightening the set
screws.
NOTE:
At least three set screws must come in contact
with the pipe.
6.
Hook the combined plate and switcher into the PMK 560 base
plate (
4
). Secure it to the base plate with two screws.
PMK Covers (2)
Base Plate
To open, remove 4 cover screws
and slide the covers away.
Mounting Plate
LAN
1
LAN
3
LAN
2
LAN
4
L
R
DO N
OT
GRO
UND
OR S
HORT
SPEA
KER
OUTP
UTS 4/8
Ω
- - A
MAX
POW
ER
12V
HDM
I
HDM
I
1/2
SIG
LINK
SIG
LINK
3/4
5
6
INPUT
S
OUT
PU
T
AUD
IO O
UT
PVS
407D
AMPL
IFIED
AUD
IO O
UT
PAG
ING
SEN
SOR
PVT I
N
PVT
IN
L
R
AUX
OVE
R PVT
REM
OTE
VOICELIFT
LAN
INPUT
7
+V
L
R
RS-2
32
Tx Rx
IR
S
G
G
CLAS
S 2 W
IRING
LAN
Attach mounting plate
to the top of the
PoleVault switcher.
Hook the combined mounting
plate and switcher into the
base plate and secure with
screws.
Projector
Pole
Attach
Power
Supply
Attach PMK to the projector
pole pipe collar with the four
10-32 set screws.
PVS 407D
Switcher
1
2
3
4
Figure 1.
PMK 560
•
figure1
Figure 2.
Attach the mounting plate to the switcher
and secure both to the base plate.
1
figure2
