Figure 3.
KNX 100G Application Diagram
2
LED Status Indicators
C
Programming Mode LED
LED STATUS
Meaning
LED lights red
Programming mode is active
LED Off
Programming mode is not active
E
Mode LED
LED STATUS
Meaning
LED lights green
Device is working in standard operation mode
LED lights red
Programming mode is active
LED flashes green 1x...5x
Programming mode is not active
Manual operation is active
The selected tunnel (1-5) is not used and free
LED flashes orange 1x...5x Programming mode is not active
Manual operation is active
The selected tunnel (1-5) is used and free
LED flashes red
Programming mode is not active
Manual operation is not active
The device is not properly loaded for example after an interrupted download
F
IP LED
LED STATUS
Meaning
LED lights green
The device has an active Ethernet link and valid IP settings.
LED lights red
The device has an active Ethernet link and invalid IP settings or not yet received the IP settings by a
DHCP server.
LED flashes green
IP telegram traffic
D
KNX LED
LED STATUS
Meaning
LED lights green
KNX 100G successfully powered
LED flashes green
Telegram traffic on the KNX bus
LED lights red shortly Communication failure on the KNX bus
KNX 100
G
Patent(s): www.extron.com/patents
33-2700-01
A
E
E
est
est
KNX 100
G
Patent(s): www.extron.com/patents
33-2700-01
A
E
Pro
g. KN
X
__.__.____
E
KNX 100G
KN
X
Mode
IP
P/Es
c
Conn
Up
Conn
Dn
Ethernet
Twisted Pair
Cable
IPC
P P
RO
55
0
OVE
R
2
1
4
3
LIM
IT
R
IR
1
2
3
4
5
6
7
8
Tx
Rx
Tx
Rx
RT
S
CT
S
CO
M
IR/
SE
RIA
L
1
3
2
4
RE
LAY
S
FLE
X
I/O
S
LIM
IT
OVE
R
eB
US
SW
ITC
HE
D
12
VD
C
100
0
LIN
K
AC
T
2
1
5
6
3
7
4
8
2
1
5
6
3
7
4
8
Light
Shutters
Dimmer
Volume
Thermostat
(Temperature)
Dimme
Volume
KNX 100G
IPCP Pro 550
IPCP Pro 550
TLP Pro 725M
Network
IPC
P P
RO
55
0
OVE
R
2
1
4
3
LIM
IT
R
IR
1
2
3
4
5
6
7
8
Tx
Rx
Tx
Rx
RT
S
CT
S
CO
M
IR/
SE
RIA
L
1
3
2
4
RE
LAY
S
FLE
X
I/O
S
LIM
IT
OVE
R
eB
US
SW
ITC
HE
D
12
VD
C
100
0
LIN
K
AC
T
2
1
5
6
3
7
4
8
2
1
5
6
3
7
4
8
TLP Pro 725M
KNX
Bus
KNX 100G Network Installation
1.
Using a certified KNX twisted pair cable, connect to the
KNX BUS located on the top of the device (see figure 3).
2.
Connect an ethernet cable between the Ethernet port
located at the bottom of the KNX 100G and the local
network.
3.
Configure the KNX 100G using ETS.
4.
Configure your Extron Control System using the Extron
driver targeted at your configured KNX 100G.
NOTE:
Engineering Tool Software (ETS) is an application
for designing, commissioning, and debugging KNX
installations. Click this
link
to view and purchase ETS
for your KNX setup. KNX system setup should be done
by a certified KNX professional.