background image

FOX 4G DA8 • Reference Information

Reference Information

FOX 4G DA8 • Reference Information

 

A-2

A-3

Specifications

Optical specifications

N

 

These amplifiers are class 1 laser products.  They meet the 
safety regulations of IEC-60825, FDA 21 CFR 1040.10, and 
FDA 21 CFR 1040.11.

Number/type

Input ....................................  1 singlemode or multimode fiber optic
Output .................................  8 singlemode or multimode fiber optic

Connectors .....................................  8 LC connectors
Operating distance ........................

  30 km (18.75 miles) with singlemode (SM) 

cables 

0.15 km (492') with multimode (MM) 

cables

N

 

Operating distance is approximate.  These are typical 
distances.  The maximum distance may be greater than these 
typical numbers depending on factors such as fiber type, fiber 
bandwidth, connector splicing, losses, modal or chromatic 
dispersion, environmental factors, and kinks.

Nominal peak wavelength

...........  850 nm for MM model, 

1310 nm for SM model

Data rate .........................................  4.25 Gbps
Transmission power

Singlemode .........................  -5 dBm, typical
Multimode ..........................  -5 dBm, typical

Maximum receiver sensitivity

Singlemode .........................  -18 dBm, typical
Multimode ..........................  -12 dBm, typical

Optical loss budget

Singlemode .........................  13 dB, maximum
Multimode ..........................  7 dB, maximum

Control/remote

Serial control ports ........................  1 RS-232, 3.5 mm captive screw connector, 

3 pole (rear panel) 

1 RS-232, 2.5 mm mini stereo jack

 

(front panel)

Baud rate and protocol .................

  9600 baud, 8 data bits, 1 stop bit, no parity

Serial control pin configurations .  Captive screw connector: 1 = TX, 2 = RX, 

3 = GND 

Mini stereo jack: tip = TX, ring = RX, 

sleeve = GND

Program control .............................  Extron's control/configuration program 

for Windows

®

 

Extron's Simple Instruction Set (SIS

)

General

Power ..............................................

  100 VAC to 240 VAC, 50-60 Hz, 20 watts, 

internal

Temperature/humidity ................  Storage: -40 to +158 °F (-40 to +70 °C) / 

10% to 90%, noncondensing

 

Operating: +32 to +122 °F (0 to +50 °C) / 

10% to 90%, noncondensing

Cooling ...........................................  Convection, vents on top and sides
Mounting

Rack mount

 ........................

  Yes, with optional 1U, 9.5" deep rack shelf)

Furniture mount ................

  Yes, with optional under-desk mounting 

kit and through-desk mounting kit

Enclosure type ...............................  Metal
Enclosure dimensions ...................

  1.7" H x 8.7" W x 9.5" D

 

(1U high, half rack wide)

 

(4.3 cm H x 22.1 cm W x 24.1 cm D)

 

(Depth excludes connectors.)

Product weight ..............................

  2.3 lbs (1 kg)

Shipping weight ............................

  4 lbs (2 kg)

Vibration .........................................  ISTA 1A in carton 

(International Safe Transit Association)

Regulatory compliance

Safety ...................................

  CE, CUL, UL

EMI/EMC ..........................

  CE, C-tick, FCC Class A, FDA Class 1, 

ICES, VCCI,

MTBF ...............................................  30,000 hours
Warranty .........................................  3 years parts and labor

N

 

All nominal levels are at ±10%.

N

 

Specifications are subject to change without notice.

Summary of Contents for Fiber Optics Fox 4G DA8























Reviews: