background image

 

安全须知 

 中文

这个符号提示用户该设备用户手册中
有重要的操作和维护说明。

这个符号警告用户该设备机壳内有暴

露的危险电压,有触电危险。

注意

阅读说明书 

• 

用 户 使 用 该 设 备 前 必 须 阅 读 并 理

解 所 有 安 全 和 使 用 说 明 。

保存说明书 

• 

用户应保存安全说明书以备将来使

用。

遵守警告 

• 

用户应遵守产品和用户指南上的所有安

全和操作说明。

避免追加 

• 

不要使用该产品厂商没有推荐的工具或

追加设备,以避免危险。

警告

电源 

• 

该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。   设 备

必 须 使 用 有 地 线 的 供 电 系 统 供 电 。   第 三 条 线
( 地 线 ) 是 安 全 设 施 , 不 能 不 用 或 跳 过 。

拔掉电源 

• 

为安全地从设备拔掉电源,请拔掉所有设备后

或桌面电源的电源线,或任何接到市电系统的电源线。

电源线保护 

• 

妥善布线, 避免被踩踏,或重物挤压。

维护 

 所有维修必须由认证的维修人员进行。 设备内部没

有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。

通风孔 

• 

有些设备机壳上有通风槽或孔,它们是用来防止

机内敏感元件过热。 不要用任何东西挡住通风孔。

锂电池 

• 

不正确的更换电池会有爆炸的危险。 必须使用与

厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to part 15 of the FCC Rules.  Operation is subject to the following two conditions: (1) this 

device may not cause harmful interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation.  The Class A limits are designed to 

provide reasonable protection against harmful interference when the equipment is operated in 

a commercial  environment.  This equipment generates, uses, and can radiate radio frequency 

energy and, if not installed and used in accordance with the instruction manual, may cause harmful 

interference to radio communications.  Operation of this equipment in a residential area is likely to 

cause harmful interference, in which case the user will be required to correct the interference at his 

own expense.

Summary of Contents for Fiber Optics Fox 4G DA8























Reviews: