Extron electronics Extron IPL T S4 User Manual Download Page 58

Page: 58 / 79

Communication and Control, cont’d

IPL T S Series • Communication and Control

4-18

Command

ASCII (T

elnet)

(host to unit)

URL Encoded (W

eb)

(host to unit)

Response

(unit to host)

Additional description

Absolute system

reset

ZQQQ

}

ZQQQ

Zpq

]

This r

esets all device settings/memories

to factory default; however

, the firmwar

version r

emains the same. This includes all

settings, adjustments, PINs, the IP

addr

ess,

and subnet mask. Files in flash memory ar

also erased by this command.

The IP

addr

ess is r

eset to 192.168.254.254,

the subnet mask is r

eset to 255.255.0.0.

This command is identical to r

eset mode

discussed in “Resetting the Unit” in

chapter

Unlike various PC operating systems, a file and dir

ectory on the Extr

on pr

oduct ar

e allowed to have the same name.

Summary of Contents for Extron IPL T S4
















































































Search results

Summary of Contents for Extron IPL T S4

Reviews:

Related manuals for Extron IPL T S4

Brands by name

Popular brands

Extron electronics Extron IPL T S4, User Manual

Search results

Summary of Contents for Extron IPL T S4

Reviews:

Related manuals for Extron IPL T S4

Brands by name

Popular brands