background image

2

EBP 100/200 Series • Setup Guide (Continued)

Rear Panel Features

PWR LO

AD = 0.5W

PWR LO

AD = 0.5W

ON

123456

BUS ID

M

S

B

L

S

B

ON

12

3456

eBU

S

G

-S

+S

+V

G

-S

+S

+V

EBP 100 Rear Panel

C

C

C

C

D

D

D

D

B

B

B

B

A

A

A

A

Figure 2. 

EBP Rear Panel Features

Planning the System and Installation

When planning to install an eBUS system you must consider how many EBP button panels to use, maximum cable distance, 
cabling topology, and mounting. See the 

EBP 100 and EBP 200 User Guide

 for more information about eBUS topologies.

Installation

Step 1: Get Ready

Use the following check list to prepare for the installation.

 

…

Download and install the latest version of the software, firmware, and device drivers needed to configure the IPCP Pro and 
control the connected AV products. See the 

IPCP Pro Series User Guide

 (available on the Extron website) for details on 

software and drivers.

 

…

Obtain network information (IP addresses, passwords, DHCP settings, and the like) and the MAC address for the control 
processor.

 

…

Obtain model names, drivers, and setup information for AV devices.

 

…

Determine which eBUS cabling topologies to use and obtain cables, mounting hardware, and any power supplies or hubs 
required by that configuration.

Step 2: Prepare the Installation Site

ATTENTION:

 

• 

Installation and service must be performed by authorized personnel only.

• 

L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• 

Extron recommends installing the EBP into a grounded, UL Listed electrical junction box.

• 

Extron recommande d’installer le EBP dans un boîtier d’encastrement électrique mis à la terre, listé UL.

• 

If the EBP will be installed into fine furniture, it is best to hire a licenced, bonded craftsperson to cut the access hole 
and perform the physical installation so the surface will not be damaged.

• 

S’il est prévu d’installer le EBP dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et qualifié 
pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• 

Follow all national and local building and electrical codes that apply to the installation site.

• 

Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE:

  For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the EBP must be 

installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with the 
EBP 100 or EBP 200.

NOTE:

  For rear panel features, all models are identical.

A

 Bus ID DIP switches

B

 eBUS ports

C

 eBUS status LED

D

 Maximum power load rating

Summary of Contents for EBP 100









Reviews: