manualshive.com logo in svg

Extron electronics DXP 1616 HD 4K, User Manual, Page: 14 / 116

Share
Download
Extron electronics DXP 1616 HD 4K User Manual Download Page 14

DXP HD 4K Series • Installation

6

Installation

This section describes the rear panels of the DXP HD 4K switchers and provides 
instructions for cabling. It covers the following topics:

• 

Rear Panels

• 

Connecting to the LAN Port

• 

Connecting to the Remote RS-232 Port

• 

Connecting to the USB Config Port

Rear Panels

Most of the connectors are on the rear panels of the DXP HD 4K switchers. 

Figures 3 and 

4

 on the next page show the rear panels of a DXP 88 series model and a DXP 1616 series 

model.

WARNING:

  Remove power from the system before making any connections.

AVERTISSEMENT :

  Couper l’alimentation avant de faire l’installation électrique.

ATTENTION:

 

• 

Use electrostatic discharge precautions (be electrically grounded) when making 
connections. Electrostatic discharge (ESD) can damage equipment, although you 
may not feel, see, or hear it.

• 

Prenez des précautions contre les décharges électrostatiques (soyez 
électriquement relié à la terre) lorsque vous effectuez des connexions. Les 
décharges électrostatiques (ESD) peuvent endommager l’équipement, même si 
vous ne pouvez pas le sentir, le voir ou l’entendre.

Summary of Contents for DXP 1616 HD 4K





















































































































Reviews:

No comments