manualshive.com logo in svg

Extron electronics DXP 1616 HD 4K, User Manual, Page: 19 / 116

Share
Download
Extron electronics DXP 1616 HD 4K User Manual Download Page 19

 

DXP HD 4K Series • Installation

11

Connecting to the Remote RS-232 Port

The DXP HD 4K switchers have a rear panel Remote serial port through which they can 
be configured via SIS commands (serial commands that control the switcher through this 
connector).
Wire the 3.5 mm captive screw Remote RS-232 connector as shown in figure 8.

Computer or
Control System
RS-232 Port

DXP HD 4K
Rear Panel
RS-232 Port

NOTES:  

 

•

  If you use cable that has a drain wire, tie  

the drain wire to ground at both ends.

 

•

  Connect a ground wire between the DXP

and the computer or control system.

Tx Rx G

Tx Rx G

Ground (G) 

Transmit (Tx) 

Receive (Rx) 

Transmit (Tx)

Receive (Rx)

Figure 8. 

Wiring the Remote RS-232 Connector

See 

SIS Configuration and Control

, starting on page 57, for definitions of the SIS 

commands and 

Configuration Software

, starting on page 81, for details on how to install 

and use the control software.

NOTES:

 

• 

The switcher operates at 9600, 19200, 38400, or 115200 baud.

• 

See 

Selecting the Remote RS-232 Port Baud Rate

 on page 51 to configure this 

port using the front panel buttons.

If desired, you can connect an MKP 2000 or MKP 3000 remote control panel to this port. 
See the user guide of either product for details.

Summary of Contents for DXP 1616 HD 4K





















































































































Reviews:

No comments