Extron electronics Digital Video Transmitter and Receiver DVI 201 Rx, User Manual

Page: 19 / 30

DVI 201 Tx/Rx • Installation and Operation
Installation and Operation, cont’d
2-22
DVI 201 Tx/Rx • Installation and Operation
2-23
l
RS-232 connector — Connect a serial communications port to
this 3.5 mm, 3-pole captive screw connector for bidirectional
RS-232 communication. See "RS-232 connector wiring," on
page 2-26, to wire the connector.
N
The RS-232 connector can also transmit one-way
modulated infrared (IR) signals. See "Modulated IR
pass through" on page 2-33.
m
Audio output connector (DVI 201 A D Tx [Decora] only) —
Connect a stereo audio device to this 3.5 mm mini stereo jack to
receive the unbalanced audio output. Figure 2-14 on page 2-17
shows how to wire the audio plug.
Pin assignments and wiring
DVI connector pin assignments
Figure 2-19 defines the pinout for the DVI protocol.
Pin Signal
1 TMDS data 2–
TMDS data 2+
TMDS data 1–
TMDS data 1+
DDC clock +5 V power
DDC data TMDS clock+ Ground (+5 V)
CEC control* TMDS clock– Hot Plug Detect
TMDS data 0–
TMDS data 0+
Spare
Spare
Spare
Spare
Spare
Spare
TMDS data 2
shield
TMDS data 1
shield
TMDS data 0
shield
TMDS clock
Shield
Pin Pin Signal Signal
2
9
10
17
4 12 20
5 13 21
6 14 22
7 15 23
8
* CEC control on pin 8 is a proprietary usage,
not the industry standard.
16 24
18
3 11 19
1
9
8
17 24
Female Connector
Male Connector
Figure 2-19 — DVI connectors
TP cable termination
N RJ-45 termination with CAT 5, CAT 5e, or
CAT 6 cable must comply with the TIA/EIA T 568A or
TIA/EIA T 568B wiring standard for all connections.
Figure 2-20 details the recommended termination of TP cables
with RJ-45 connectors in accordance with either the
TIA/EIA T 568A or the TIA/EIA T 568B wiring standard.
5
Pin
1
2
3
6
7
8
4
N
Terminate both ends of both cables identically, in accordance with
either the TIA/EIA T 568A or the TIA/EIA T 568B wiring standard.
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
Data 0+
Data 0–
Data 1–
ID Clock–
Data 2+
Data 2–
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Signal
TIA/EIA T
586 A
TIA/EIA T
586 B
RJ-45 #1
ID Clock+
Data 1+ Blue
CEC
HPD
RS-232
TX
+12 V
RS-232
RX
DDC data
Ground
RJ-45 #2
DDC Clk
Side
12345678
Insert
Twisted
Pair Wires
Pins:
RJ-45
Connector
Figure 2-20 — TP cable termination
N Do not use Extron’s UTP23SF-4 Enhanced Skew-Free
™
A/V UTP cable to link the transmitter and receiver.
Skew-free A/V cable was designed for most Extron
TP transmitter/receiver applications, but the
DVI 201 Tx/Rx will not work properly with this cable.
N In order to fit in the junction box, the TP cables and
RJ-45 connectors should not have a boot installed.
N If necessary, test for proper cable connection (output 1 to
input 1, output 2 to input 2) as follows:
1 . Plug both TP cables into the powered unit.
2 . Momentarily connect either of the cables on the
opposite end into the unpowered unit‘s “2” connector.
If the unpowered unit’s Power LED is lit , the
connection is correct.
If the unpowered unit’s Power LED is not lit ,
unplug the connector on the unpowered end and
connect the other cable to the “2” connector.