background image

DVI 201 Tx/Rx • Installation and Operation

Installation and Operation, cont’d

2-10

DVI 201 Tx/Rx • Installation and Operation

 

2-11

6

Assemble the U-bolt and the following parts in the 

following order (figure 2-8):

a

.  Pass the legs of the U-bolt through the slotted holes on 

the mount plate flange.

b

.  Place the legs around the projector pole.

c

.  Pass the legs through the holes in the contour base.

N

 

The pole fits snugly into the depression in the 

center of the contoured base.

d

.  Pass the legs through the holes in the L-shaped bracket.

N

 

The supplied U-bolt fits a typical (1.5" to 2.0" 

diameter) ceiling pole.

U-bolt

Slotted Hole
in PMK Tray

L-shaped
Bracket

L-shaped
Bracket Screws

Contoured
Base

Ceiling
Pole

Mount Plate
Flange

Figure 2-8 — Hanging the tray on the pole

7

Align the two slotted holes in the bottom of the L-shaped 

bracket with the two slotted holes in the base of the tray.  

Secure the L-bracket to the base by inserting two provided 

6-32 x 5/16" screws through the aligned slots.

8

Move the PMK 350 up to the desired location on the ceiling 

pole, as close to the ceiling as desired.

9

Secure the L-shaped bracket to the U-bolt using the 

included hex nuts, washers, and lock washers.  Tighten the 

hex nuts securely.

N

 

Be sure to tighten the hex nuts securely enough that the 

PMK 350 does not slide down the ceiling pole.  A socket 

wrench is recommended to tighten the hex nuts.

10

.  Secure the front and rear plates to the mounting tray with 

four of the included #6 screws.

11

.  If desired, choose one of the provided four sizes of self-

adhesive cover sheets, and apply it to the underside of the 

mounting tray.

Decora unit mounting

The DVI 201 A D (Decora) transmitter and receiver can be 

installed in a one-gang electrical wall box with a Decora wall 

plate cover (supplied).
The installation must conform to national and local electrical 

codes and to the wall plate’s size requirements.

UL/Safety Requirements

The following Underwriters Laboratories (UL) requirements 

pertain to the installation of the Decora transmitters and 

receivers into a wall or furniture.

1

These units are not to be connected to a centralized DC 

power source or used beyond their rated voltage range.

2

These units must be installed in UL listed junction boxes.

3

These units must be installed with conduit in accordance 

with National Electrical Code.

Preparing the site and installing the wall box

Choose a location that allows cable runs without interference.  

Allow enough depth for both the wall box and the cables.  The 

box should be at least 2.5" (6.4 cm) deep to accommodate the 

connectors and cables.  Install the cables into the wall, furniture, 

or conduits before installing the wall plate.

N

 

The Decora units are very deep and have connectors 

on the back side (figure 2-9 on page 2-12).  Extron 

recommends its 1-gang or 2-gang junction boxes 

(part #s 

980130

 or 

980084

), which have a depth of 

2.5" (6.4 cm).

Summary of Contents for Digital Video Transmitter and Receiver DVI 201 Rx































Reviews: