background image

Verwenden Sie nur Netzkabel mit Schutzerdung. Ohne ordnungsgemäße Schutzerdung besteht

für Personen, die den Switch berühren, die Gefahr eines elektrischen Schlages. Eine

nichtvorhandene Schutzerdung kann zu sehr starken Abstrahlungen führen.

Danger:

N'utilisez que des cordons d'alimentation équipés de trajet de mise à la terre. Sans mise à la

terre adaptée, vous risquez de recevoir une décharge électrique en touchant le commutateur.

Par ailleurs, l'absence de trajet de mise à la terre peut générer des émissions excessives.

Important:

Peligro:

Utilice únicamente cables de alimentación con toma de tierra. De lo contrario, al tocar el

interruptor puede recibir una descarga eléctrica. Si no hay un circuito de toma de tierra en el

enchufe, puede producirse un exceso de emisiones.

Important:

Pericolo:

Utilizzare esclusivamente cavi di alimentazione dotati di un percorso per la messa a terra.

Senza un'adeguata messa a terra, chiunque tocchi lo switch corre il rischio di ricevere una

scossa elettrica. L'assenza di un percorso per la messa a terra verso lo switch può comportare

un eccesso di emissioni.

Warning:

The lithium battery is not field replaceable. It must only be removed and replaced by authorized

personnel. Contact Extreme Networks Technical Support for assistance if the battery requires

replacement.

Important:

Warnung:

Die Lithiumbatterie kann nicht vor Ort ausgetauscht werden. Die Batterie darf nur von

entsprechend befugtem Personal entfernt und ausgetauscht werden. Muss die Batterie ersetzt

werden, wenden Sie sich bitte an den Technischen Support von Extreme Networks.

Important:

Avertissement:

La batterie au lithium n'est pas remplaçable sur site. Elle ne peut être enlevée et remplacée que

par du personnel qualifié. Veuillez prendre contact avec le support technique d'Extreme

Networks si la batterie doit être remplacée.

Translations of safety messages

August 2018

Installing the Virtual Services Platform 4450GSX-PWR+

44

Summary of Contents for EC4400004-E6














































Reviews: