manualshive.com logo in svg

Extraflame ANGELA, User Manual

Share
Download
Extraflame ANGELA User Manual Download Page 21

ENGLISH

chrOnO

This function allows the programming of automatic stove ignition and switch-off.

By factory default 

CHRONO

 is disabled.

The chrono allows the programming of 4 time slots within a day, which can be used every day of the week. 

For each time slot, it is possible to set ignition and switch-off times, specific days of application, desired temperature and set power. 

current day and time settings are essential for the correct operation of the chrono.

Recommendations

Before using the chrono function, the current day and time need to be set. Therefore, check that the steps listed in the sub-chapter 
“

SeT clocK

” have been carried out. for the chrono to work properly, it must be programmed and then enabled. The 4 time slots can 

be linked through the switch-on and switch-off times. In this way, it is possible to create a combination of time slots with different 
temperatures and power levels, without changing the status of the stove. 

N.B.: in the case of multiple linked time slots, the product will remain on until the last switch-off time. 

prG 1-4

prg x allows to set the on/off time, the days of use of the scheduled time slot, the desired temperature (low - 7° - 40° - hot) and also the desired 

power level. current day and time settings are essential for the correct operation of the chrono.

To set: 

oK > chroNo > prgx

enaBlInG

Allows the chrono and the different stove time slots to be enabled/disabled.

To set: 

oK > chroNo > eNaBLe.

1. Enable prg x

2. On time prg x

3. Off time prg x

4. Enable days prg x

5. Set temperature prg x

6. Set power prg x

21

Summary of Contents for ANGELA





































Reviews:

No comments

Brands by name

Popular brands

Load more brands