background image

Form No. 4503-816 Rev A

Operator's Manual

42 Inch Bagger

Quest

®

Model No. 126-7506—Serial No. 402082300 and Up

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California

to cause cancer, birth defects, or reproductive harm.

Important:

This kit requires the simultaneous installation of other kits to function properly. Lever steer

units require a front weight kit and a mounting kit. Steering wheel units require a mounting kit. Contact
your Authorized Service Dealer to obtain the corresponding necessary parts.

Introduction

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

Whenever you need service, genuine parts, or
additional information, contact an Authorized Service
Dealer or Customer Service and have the model
and serial numbers of your product ready.

Figure 1

identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

g207309

Figure 1

1.

Model and serial number location

Model No.

Serial No.

For complete warranty details, see
http://www.Exmark.com. You may also call us
402-223-6375 to request a written copy of the
product’s warranty.

This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

1.

Safety-alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

© 2017—Exmark Mfg. Co., Inc.
Industrial Park Box 808
Beatrice, NE 68310

www.Exmark.com

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*4503-816* A

 

Summary of Contents for Quest 126-7506

























Reviews: