Excellent KERIA Installation Instructions Manual Download Page 21

21

Instructions for installation and use

lmportant !

Pressure! System operating pressure is 3 Bar; additionally, pressure differences between the cold 

and hot water connections prevent the correct functioning of the water mixer; therefore, water pres

-

sure must be leveled prior to connecting the kit. Using valves in water flow systems that use tankless 

water flow heaters or the so-called boilers does not ensure proper functioning of the kit.

Warning! 

To avoid scratches and damage to kit surfaces, wear protective gloves when assembling/installing

-

the system.

lnstalling instructions:

• 

Failure to fol low installation instructions may result in product damage and the rejection of 

claim.

• 

Prior to installation, check the product for transport damage. Damage, even though it will not be 

visible, can significantly affect system performance after the installation.

• 

Water systems should be equipped with filters blocking mechanical impurities. 

• 

Kits must not be installed in rooms where the temperature falls below 4 °C.

• 

Pipes and fittings must be installed, flushed and inspected according to the applicable stan

-

dards in terms of standard pressure and hardness of the water. For atypical situations, increase 

the frequency of flushing , cleaning and inspecting components and pipes. 

• 

Follow the installation guidelines for your country.

• 

Refer to the list of prohibited activities that result in the rejection of a potentiaI claim.

• 

Use the product gaskets/washers supplied with the product (also if they are listed as necessary 

but are not supplied); if leakage occurs during testing, use additional sealants.

• 

lnstallation should be performed by a qualified installer.

• 

Product installation should take into account the ease of service access without removing other 

devices or structures.

Care and maintenance:

• 

Failure to use proper care and maintenance may result in product damage and the rejection of 

claim.

• 

To clean all surfaces, use only a soft cloth (microfiber) and mild detergents (like soap) and then 

rinse thoroughly with clean water and dry with a soft cloth. Remove lime deposits using a mild 

dishwasher liquid.

EN

Summary of Contents for KERIA

























Reviews: