Page - 9
Transmitter Operations
Large Upper Button- Pressing
and releasing this button will arm
and disarm the security system.
If the optional doorlock interface
is installed, the doors will lock
upon arming, and unlock upon
disarming. If you have the op-
tional unlock driver's door fea-
ture, then upon disarming only
the driver's door will unlock, and
if the large button is pressed
again within 3 seconds, all of the
doors will unlock.
Pressing and holding this but-
ton for 3 seconds will "Panic" the
system- which will sound the
siren or horn, flash the lights,
and also lock the doors.
If this button is pressed within 3 seconds
after disarming, the system will enter Remote Valet.
Pressing this button for 3 seconds may be used to activate other optional modules through
the 3rd channel output (Example: remote car starting equipment).
Small Lower Button-
If this button is pressed within
3 seconds after arming the
system, the Auxiliary sensor
will be turned off.
Small Center Button-
If this button is held
for 3 seconds, the
security system will
activate the trunk release func-
tion.
If this button is pressed and
then the large button is
pressed within 3 seconds, the
security system will arm or
disarm without audible con-
firmation.
Red LED Light- Illuminates and
confirms transmission when-
ever a button is pressed.
Page - 10
The Remote Transmitter
Transmitter Button Operation: The transmitter's three buttons individually control the
system's functions; and certain other operations may be performed by first pressing and
releasing one, then another button in sequence. Complete transmitter button operations are:
1)
Arm / Lock: (System Disarmed) Press and release the Large Upper Button.
2)
Disarm / Unlock #1: (System Armed) Press and release the Large Upper Button.
3)
Unlock #2: (After the previous step) Press and release the Large Upper Button again.
4)
Remote Panic Feature: (At any time) Press and hold the Large Upper Button 3
seconds.
5)
Trunk Release Output: (At any time) Press and hold the Small Center Button 3
seconds. This operation also disarms the system (if armed).
6)
3rd Channel Output: (At any time) Press and hold the Small Lower Button for 3
seconds.
7)
Silent Arm / Lock: (System Disarmed) Press and release the Small Center Button,
then press and release the Large Upper Button.
8)
Silent Disarm / Unlock: (System Armed) Press and release the Small Center
Button, then press and release the Large Upper Button.
9)
Arm and bypass the Auxiliary Sensor: (System Disarmed) Press and release the
Large Upper Button, then press and release the Small Lower Button.
10)
Disarm, then Remote Valet: (System Armed) Press and release the Large Upper
Button, then press and release the Small Lower Button.
Please note that certain conditions will affect the previously described system operations
- if the ignition switch is "on", the security system cannot be armed, but pressing and holding
the transmitter's Large Upper Button for 3 seconds will engage the Panic Feature. The Trunk
Release output will not operate with the ignition "on", unless a door is open. The 3rd Channel
output may be operated regardless of the ignition switch's status. Also, while in Valet Mode,
the system cannot become armed, but will still operate the vehicle's doorlocks, parking and
dome lights, trunk release, and any function operated by the 3rd Channel Output.
Multiple Car Operation - Changing Transmitter Banks: The transmitter button operations
explained on the previous pages are applicable for up to four different Excalibur Gold vehicle
security systems (i.e. - all three transmitter buttons will operate properly on one system without
affecting other systems operable by the same transmitter). This is accomplished by "changing
banks" on the transmitter:
1)
Rapidly press the transmitter's Small Center Button 4 times, holding it depressed on
the fourth press. The first three presses must be released before the transmitter's
LED lights.
2)
The transmitter LED will now be flashing 1 to 4 times between pauses. The number
of flashes indicates the current bank level (1 flash = Bank One; 2 flashes between
pauses = Bank Two; etc.). Continue to hold the Small Center Button depressed.
3)
To change banks, press and release the Large Button the number of times equal to the
desired Bank level number.
Page - 11
4)
The LED will change to flashing the new Bank level number between pauses.
5)
Release the Small Center Button. The transmitter will now operate in the new Bank.
When attempting to enter Bank Selection Mode, please note that the transmitter alter-
nates entering Bank Selection Mode and transmitting a signal. When attempting to enter
Bank Selection Mode, if the transmitter's LED rapidly flashes, it is transmitting; simply repeat
the steps listed above to enter Bank Selection Mode.
Arming The System Using The Transmitter
To "arm" your security system is to place it into a state whereby it will respond to any
detected intrusion attempt. The security system can always be armed from the transmitter
provided the ignition switch is “off”, and the system is disarmed and not in the Valet Mode.
To arm the system, after you exit the vehicle and close all of the doors, simply press and release
the large transmitter button once, Instantly the exterior and interior lights will flash once, the
siren will chirp once (or the horn will honk once) and the Visual Deterrent LED will flash rapidly
during the Arming Delay, then change to flashing slowly, confirming that the system is armed.
The Digital Status Indicator will show " " during the Arming Delay, then " " for 10 seconds
when the system becomes fully armed.
Further, the doors will lock and the starter interrupt circuit will prevent any attempt to start
the vehicle. Three seconds after the single horn honk (or siren chirp) and light flash, your
security system is fully armed, and is ready to respond if an intrusion attempt is detected.
Page - 12
