background image

11

The Status Light

  The status lights, located in the window-mount antenna, provide a visual indication 

of the system’s status via GREEN (remote start status) and RED (alarm status) lights.

SECURiTy SySTEm STATUS (RED LiGhT):

OFF:

 The alarm is disarmed and not performing any automatic functions.

On COnSTAnT:

 The alarm is in valet mode

FLAShinG SLOW: 

The alarm is armed and monitoring all entry points

FLAShinG FAST: 

One of the automatic arming features is in progress.

AUTOmATiC TRAnSmiTTER VERiFiCATiOn (RED LiGhT):

Every time you turn on the ignition key, the status light will flash a number of times 

equal to the number of controllers/transmitters programmed to the system. This 

unique security feature protects you from a potential thief (valet attendant, mechanic, 

installer, etc.) from adding their own transmitter without your knowledge and access

-

ing your vehicle and it’s contents at a later time (the perfect crime!).

ZOnE ViOLATiOn RECALL:

  If the security system is triggered, upon disarming, the RED status lights will flash 

a number of times to indicate exactly which zone(s), has been violated. It will store 

the last 2 violated circuits and continually repeat the flash pattern until the system is 

disarmed and the vehicle’s ignition key is turned On 

2 FLAShES:

 hood trigger

3 FLAShES: 

Door trigger

4 FLAShES:

 Sensor port trigger

REmOTE START STATUS (GREEn LiGhT):

OFF:

 The remote start is off and in standby mode.

On COnSTAnT:

 The remote start is in valet mode

FLAShinG SLOW: 

The engine was started successfully and is running.

FLAShinG FAST: 

The remote start sequence has begun and is in process of starting 

the vehicle’s engine

REmOTE START DiAGnOSTiCS (GREEn LiGhT):

  The remote start system can also indicate which zone caused the last remote 

start cycle was ended To see this indicator, place the system into alarm valet mode 

Immediately after the chirp, the GREEN status light will flash to indicate what caused 

remote start to end

1 FLASh:

 Run time expired

2 FLAShES:

 Brake pedal was pressed

3 FLAShES:

 Engine stalled or a bad tach signal

4 FLAShES:

 Received transmitter command to stop

5 FLAShES:

 Gear selector was moved from park(or the parking brake was released).

6 FLAShES: 

The alarm was triggered or low battery voltage

COmBinATiOn inDiCATiOnS:

  This indication reflect combinations of functions involving the security system AND 

remote start

SLOWLy ALTERnATES GREEn/RED:

 System is in full valet mode.

Summary of Contents for AL-1850-EDPB

























Reviews: