background image

 

                                                         NX1200 User Guide 

 

© 2014 ExaDigm, Inc.   

 

 

Page 14 of 16   

 

 

Rev. 1/0614 

The  application  uses  a  module  named  Transaction  Object  Interface  Processor  that  makes  sure  that  all 

Transaction Variables

” are deleted from memory after it is processed.  

Also  the  Transaction  Object  module  checks  for  the  following  conditions  before  running  a  payment 
transaction and does not allow the transaction and forces the user to perform Settlement if 

“any of” 

the 

following initial conditions fails:  

 

The  oldest  transaction  in  database  shouldn’t  be  older  than  a  configurable  “Cardholder  Retention 
Time” Variable Object.  

 

Number  of  transactions  in  database  shouldn’t  exceed  the  configurable  “Max  Transaction  Number” 
Variable Object.  

 

Total Amount of transactions in database shouldn’t exceed the configurable “Max Transaction Total” 
Variable Object.  

 

Available free flash memory space in system should be more than “Min Free Memory Size” Variable 
Object.  

16.1.3  Database Object Security Features 

 

The application uses a module named the Database Interface Processor  which gathers information from 
different  sources  to determine  whether  to  write  the  account  data  in  the  database  or  not.  These  settings 
are  all  hard  coded  and  cannot  be  accessed  by  any  user.  The  settings  are  based  on  PA-DSS 
requirements. 

The following rules are applied in Database module:  

  PIN Block Data is not stored in any case.  

  CVV Data is not stored in any case.  

  Full Magnetic Data is stored only if 

“all” 

of the following conditions are met:  

i.  If offline transaction is supported (Defined in a Configuration Variable Object)  

ii. 

“Save Full Track Data in Database” flag is active in Transaction Object  

iii.  If current transaction is performed offline (or Store and Forward).  

17.0 

Battery and Charger Safety 

Proper  battery  and  charger  safety  is  necessary  to  ensure  the  terminal  will  perform  to  its  potential  and 
reduce the risk of overheating, igniting or explosion, resulting in serious bodily harm or property damage. 

  Do not disassemble, open, crush, bend, deform, puncture, shred or attempt to modify the battery or 

charger. 

  Do not modify or remanufacture, attempt to insert foreign objects into the battery or charger, immerse 

or expose to water or other liquids, or expose to fire, explosion, or other hazards.  

  Only use the battery and charger for the terminal for which it was specified.  

  Only  use  the  battery  with  a  charging  system  that  has  been  qualified  with  the  unit.  Use  of  an 

unqualified battery or charger may present a risk of fire, explosion, leakage or other hazard.  

  Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.  

Summary of Contents for NX1200

















Reviews: