Ex-Cell ZR2700 Operation Manual Download Page 20

20- ENG

D28001

Pump oil: Refer to owners manual supplied with this unit.
Engine oil: Refer to engine manual supplied with this unit.
Some units are equipped with a low oil sensor and adequate oil must be
added or the unit will not start.

CALL

1-800-475-5660 

FOR REPAIRS AND SERVICE PART PURCHASES

QUICK FACTS

ALWAYS REFER TO THE MANUALS SUPPLIED WITH THIS UNIT

GAS

OIL

WATER

PRESSURE

ADJUSTMENT

PUMP

BY

-

PASS MODE

THERMAL

RELIEF VALVE

HOSE

ENGINE

SOAP

/

CHEMICALS

NOZZLE

MAINTENANCE

SCHEDULE

STORAGE OR
WINTERIZING

Use fresh high quality unleaded gas.
Add stabilizer to fuel tank and run engine for 5 minutes before storage.

Use only cold water.
Do not operate unit with clogged or missing water filter/screen.
Do not operate unit without adequate water supply to pump. Adequate
water supply is a minimum of 20 psi and 5 gpm.
The pressure setting is preset at the factory to achieve optimum cleaning.
If you need to lower the pressure setting, refer to the operation manual for
proper procedure. 

Pull gun trigger every 2 minutes while engine is running.
Do not allow water to freeze in pump.
For cold weather or long term storage refer to the operation manual for
proper procedure. 

Never leave unit running for more than 2 minutes without pulling gun
trigger; doing so could cause damage to pump and void warranty.

Pump is equipped with a thermal relief valve. If the water overheats, this
valve will open and allow a gush of water to escape. Once the water is
released, the valve closes allowing the pump to operate normally.

Do not allow hoses to contact the HOT engine muffler during or after use.
Never pull the hose to move the unit.
Do not adjust or attempt maintenance without consulting engine manual
or an authorized engine service center.
Add stabilizer to fuel tank and run engine for 5 minutes before storage.
Always turn on the water before starting the engine.

Use only soaps and chemicals designed for pressure washer use.

Keep nozzle unclogged.  Refer to manual for cleaning procedures.
Chemical/soap cannot be applied in high pressure setting. Only in low
setting.

Follow recommended maintenance schedule for engine & pump. Refer to
manuals.
Draw clean water through chemical inlet.
Add stabilizer to fuel tank and run engine for 5 minutes before storage.
Do not allow water to freeze in pump, gun, spray wand or hoses.
For cold weather or long term storage refer to the operation manual for
proper procedure. 

Summary of Contents for ZR2700





















Reviews: