EWM Taurus 355 Synergic S TDM Page 28 Operating Instructions Manual Download | Manualshive

Page: 28 / 50

background image

Design and function

Shielding gas supply (shielding gas cylinder for welding machine)

28

099-005219-EW501

10.06.2013

5.9

Shielding gas supply (shielding gas cylinder for welding machine)

WARNING

Risk of injury due to improper handling of shielding gas cylinders!
Improper handling and insufficient securing of shielding gas cylinders
can cause serious injuries!

•

The fastening elements must tightly enclose the shielding gas cylinder!

•

Attach the fastening elements within the upper half of the shielding gas

cylinder!

•

Do not attach any element to the shielding gas cylinder valve!

•

Observe the instructions from the gas manufacturer and any relevant

regulations concerning the use of compressed air!

•

Avoid heating the shielding gas cylinder!

CAUTION

Faults in the shielding gas supply.
An unhindered shielding gas supply from the shielding gas cylinder to the welding
torch is a fundamental requirement for optimum welding results. In addition, a blocked
shielding gas supply may result in the welding torch being destroyed.

•

Always re-fit the yellow protective cap when not using the shielding gas connection.

•

All shielding gas connections must be gas tight.

NOTE

Before connecting the pressure regulator to the gas cylinder, open the cylinder valve
briefly to expel any dirt.

Figure 5-6

Item Symbol

Description

0

1

Pressure regulator

2

Shielding gas cylinder

3

Output side of the pressure regulator

4

Cylinder valve

•

Place the shielding gas cylinder into the relevant cylinder bracket.

•

Secure the shielding gas cylinder using a securing chain.

•

Tighten the pressure regulator screw connection on the gas bottle valve to be gas-tight.

•

Screw the gas hose (intermediate hose package) to the pressure regulator ensuring that it is gas tight.

«
...
26
27
28
29
30
...
»

Summary of Contents for Taurus 355 Synergic S TDM



















































Reviews:

No comments

Related manuals for Taurus 355 Synergic S TDM

Brand: Samsung Pages: 2

Brand: Samsung Pages: 33

Brand: Campbell Hausfeld Pages: 12

Brand: Campbell Hausfeld Pages: 44

Brand: E-Mu Pages: 72

Brand: E-Mu Pages: 44

Brand: Q-See Pages: 141

Brand: Uniden Pages: 32

Force i Monitor

Brand: Electro-Voice Pages: 6

ACCUVOICE AV205

Brand: Zvox Audio Pages: 2

Brand: CTE Pages: 130

Brand: JAMO Pages: 72

Brand: Ecco Pages: 4

MOVIE CD 1500 - TEST NEWS

Brand: Canton Pages: 1

Brand: Chuango Pages: 18

Brand: Campbell Hausfeld Pages: 68

Brand: Skytec Pages: 30

Brand: V-Tec Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands