EWM Taurus 351 Basic FKG Operating Instructions Manual Download Page 35 | Manualshive

Page: 35 / 74

background image

Design and function

MIG/MAG welding

099-005425-EW501

14.07.2016

35

5.3.2

Wire feed

CAUTION

Risk of injury due to moving parts!
The wire feeders are equipped with moving parts, which can trap hands, hair, clothing
or tools and thus injure persons!

• Do not reach into rotating or moving parts or drive components!
• Keep casing covers or protective caps closed during operation!

Risk of injury due to welding wire escaping in an unpredictable manner!
Welding wire can be conveyed at very high speeds and, if conveyed incorrectly, may
escape in an uncontrolled manner and injure persons!

• Before mains connection, set up the complete wire guide system from the wire spool to the

welding torch!

• Check wire guide at regular intervals!
• Keep all casing covers or protective caps closed during operation!

5.3.2.1 Open the protective flap of the wire feeder

To perform the following steps, the protective flap of the wire feeder needs to be opened. Make
sure to close the protective flap again before starting to work.

• Unlock and open protective flap.

«
...
33
34
35
36
37
...
»

Summary of Contents for Taurus 351 Basic FKG











































































Reviews:

No comments

Related manuals for Taurus 351 Basic FKG

Brand: Eaton Pages: 32

Brand: CAME Pages: 104

Brand: Zenith Pages: 14

Brand: Rafiki Protection Pages: 32

Brand: Zazen Pages: 8

Brand: Polk Mono Pages: 86

Brand: RED SHIELD Pages: 25

Brand: Aichi Pages: 54

Brand: CIGWELD Pages: 116

Brand: Umirs Europe Pages: 24

Brand: Valx Pages: 28

Brand: CAME Pages: 40

Brand: Xcel-Arc Pages: 20

CMD-4000 Series

Brand: Dakota Digital Pages: 6

Brand: JBL Pages: 11

Liftkar SAL Uni

Brand: SANO Pages: 24

Brand: Longevity Pages: 25

3D TRASAR Series

Brand: Nalco Pages: 243

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands