EWM T4.04 Operating Instructions Manual Download | Manualshive

Page: 35 / 54

background image

Functional characteristics

TIG welding

099-00T404-EW501

02.07.2020

35

5.1.9.8 Configuring the TIG potentiometer torch connection

DANGER

Risk of injury due to electrical voltage after switching off!
Working on an open machine can lead to fatal injuries!
Capacitors are loaded with electrical voltage during operation. Voltage remains present
for up to four minutes after the mains plug is removed.

1.  Switch off machine.
2.  Remove the mains plug.
3.  Wait for at last 4 minutes until the capacitors have discharged!

WARNING

Do not carry out any unauthorised repairs or modifications!
To avoid injury and equipment damage, the unit must only be repaired or modified by
specialist, skilled persons!
The warranty becomes null and void in the event of unauthorised interference.

• Appoint only skilled persons for repair work (trained service personnel)!

Dangers resulting from failure to perform test after conversion!
Before reconnection, “Inspection and Testing during Operation” according to
IEC/BS EN 60974-

4 “Arc welding systems – Inspection and Testing during Operation”

has to be performed!

• Perform test to IEC / DIN EN 60974-4!

When connecting a potentiometer torch, jumper JP27 on PCB T320/1 inside the welding machine
should be unplugged.

Welding torch configuration

Setting

Prepared for TIG standard or up/down torch (factory setting)



JP27

Prepared for potentiometer torches



JP27

Figure 5-22

This torch type requires the welding machine to be set to torch mode 3

> see 5.1.9.2 chapter

.

«
...
33
34
35
36
37
...
»

Summary of Contents for T4.04























































Reviews:

No comments

Related manuals for T4.04

Brand: iDance Pages: 25

Brand: Eco Pages: 2

Brand: Rafiki Protection Pages: 32

Brand: Samsung Wisenet Pages: 16

Brand: Safety Clamps Pages: 16

Brand: Kidde Pages: 10

Brand: Gemini Pages: 10

Brand: iLive Pages: 16

Brand: Adamson Systems Engineering Pages: 12

Brand: Miller Pages: 40

XC Filter Cartridge EV9613-09

Brand: Everpure Pages: 2

Brand: Parweld Pages: 16

Brand: Fender Pages: 51

Brand: POBEL Pages: 9

Brand: Velleman Pages: 8

Brand: Dantel Pages: 8

Brand: Telpro Pages: 6

Brand: AUSTRALIAN MONITOR Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands