EVOKO EM1001 User Manual Download Page 8

EVOKO MINTO

USER MANUAL

8

7.

Auto power off

After 10 minutes of inactivity you will hear
the voice feedback ”Auto power off in 10
seconds”. You will then hear: ”Press any
button to abort” . Press any button on the
Evoko Minto to abort the automatic power
off. If no button is pressed within the 10
seconds, the unit will power off to save
battery power.

NOTE:

When an audio cable is connected, the auto power

off function is disabled. If there is an active Bluetooth

connec- tion, the unit will stay on for 30 minutes before

going into Automatic disconnect (see more in the

Bluetooth section below) before the Auto power off timer

starts.

8.

More about

connections

1.

Audio cable.

a.

The audio cable connection has the

highest priority.

b.

Pressing the Bluetooth button will activate

voice feedback: “Please remove audio cable

before Bluetooth pairing” and maintain

existing audio cable connection.

c.

Inserting a micro USB cable will initiate

charging, if the cable is connected to the

device that will supply power, and keep

existing 3.5mm cable connection.

NOTE:

The audio cable used is an analog audio cable

with a 4-pole 3.5 mm connector that works with most

mobile phones. Some phone models however use the 3-

pole connector.

2.

USB cable.

a.

If an audio cable is connected, it has a
higher priority and makes the USB
connection MUTE.

b.

If the Bluetooth button is pressed, it has

higher priority and the device will switch to

Bluetooth and initiate Bluetooth pairing.

c.

The USB cable also provides power for

the Evoko Minto. Charging with USB can

also be done if the audio cable is

connected or a Bluetooth connection is

active.

3.

Bluetooth connection.

a.

If the USB cable is connected, it will

initiate and maintain the existing

Bluetooth connection.

b.

If the audio cable is connected, it has

higher priority and makes the Bluetooth

connection mute. However, if the audio

cable is removed and the Bluetooth call

is still active the call will be resumed.

c.

Cancel ongoing pairing or remove active

connection:

Hold down the Bluetooth

button to cancel Bluetooth pairing.

d.

Failed paring:

Device will attempt pairing

for 40 sec. If the pairing fails, please

check the following and try again:

i.

Make sure the device you are trying to

connect has Bluetooth activated, is in

visible mode and is within 10m from the

Evoko Minto.

ii.

Make sure that the correct Evoko Minto

unit is selected from the list of

Bluetooth devices.

e.

Automatic disconnect:

After 30 minutes of

inactivity, the voice feedback ”Bluetooth

will disconnect in 10 seconds. Press any

button to abort.” will be played. Press any

button on the Evoko Minto to abort the

automatic dis- connection. If no button is

pressed within the 10 seconds, the

Bluetooth connection will be removed to

save battery power.

f.

Bluetooth during Wall Mount

(loudspeaker model):

The device can be

used as a wireless audio speaker when in

the Wall Mount. Pairing is initiated by

pressing the Bluetooth button, but works

in the same way as regular pairing

described above.

g.

Auto Pair Mode:

Evoko Minto is often

connected to the same device

. Auto

Pairing Mode creates an easy pairing

procedure and means that one specific

device (Auto Pair Device) can be specified

for automatic pairing at Power up of

Minto. Auto Pair Mode is activated by

specifying what device Minto should Auto

Pair with:

1.

Pair Minto with the device (Auto

Summary of Contents for EM1001













Reviews: