EvoJet 0288 Manual Download Page 2

Page: 2 / 23

Jetronic-BOX HV Instructions 2.1

Contents

Introduction .........................................................................................................................3

Schematic Overview 'Doorsequencer'...............................................................................4

Factory Setting 'Doorsequencer'.......................................................................................5

Jetronic Display EDT (Engine Data Terminal)...................................................................6

JETRONIC-BOX – Setup......................................................................................................7

1:BOX-SETUP Menu.............................................................................................................8

2:RC-CONTROL Menu........................................................................................................11

3/4/5: RC-3/4/5-CONTROL Menu.......................................................................................14

6:TEST-DEVICES Menu ....................................................................................................17

CE - Konformitätserklärung / Conformity Declaration / Déclaration de conformitè ..22

Summary of Contents for 0288























