evoheat CS57, Installation And Operation Manual

Page: 10 / 17

10
4.Usage and Operation
4.2.3 Temperature setting
On the state of power on or power off, you could set the heating or cooling temperature.
Press
“ ”
and hold for 5s to enter into the parameter setting interface. Press
“ ”
(Up)or
“ ”
(Down) to choose the needed setting. Press
“ ”
to confirm. Press
“ ”
again to enter into the corresponding parameter setting interface. Pressing
“ ”
or
“ ”
could increase or decrease the value of the parameters. Press
“ ”
conserve settings.Back
the previous interface press
“ ”
.
The setting of parameters will effect the performance and efficiency of the unit. Do not make any
change of them when it is not necessary. r01/r02/r03/r04 are permitted to set by the users. For
the default values please refer to
“
Parameters Table
”
.
The permitted setting are shown as below (take r01 for example)
：
Continually press
“ ”
press “ ”
or “ ” select "r"
Press “ ”
Press “ ”
Press “ ”
or “ ”
press “ ” to
save setting
Press “ ”
to return back to
the fomer
interface
Cooling temperature set value
CAREDL
μ
C
DIN
2
1
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
Sel
Sel
Sel
Sel
Prg
mute
Sel
Sel
Sel
Sel
Prg
mute
9
4.Usage and Operation
4.2.The operation of the wire controller
4.2.1 Turn on/off
On the state of power off, pressing(for 5s)
“ ”
or
“ ”
could start the unit. The screen
displays the mode and water inlet temperature
；
On the state of power on
，
pressing(for 5s)
“ ”
or
“ ”
could turn off the unit. For the
corresponding modes please refer to the corresponding buttons. The screen shows the water
inlet temperature.
Press
“ ”
the system will be heating;
Press
“ ”
the system will be heating.
Continually press
“ ”
Continually press
“ ”
On the state of standby
On the state of power on
4.2.2 Check the parameters
On the state of power on or power off, the measured temperature of B01-B04 could be
checked. Press
“ ”
or
“ ”
to enter into the temperature interface. Press
“ ”
(Up)or
“ ”
(Down) to find the needed temperature, then press
“ ”
to check it. Press
“ ”
to return back to the previous interface.
B01:Inlet water temp.
；
B02:Outlet water temp.
；
B03:Coil temp.
；
B04:Ambient temp.
press “ ”
or “ ”
Press “ ”
Press “ ”
back to the
former
interface
The water inlet
temperature is 20.8
℃
Water inlet temperature Water inlet temperature
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
1
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
1
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
1
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
CAREDL
μ
C
DIN
2
Prg
mute
Sel
clear
Sel
Prg
mute
Sel
Prg
mute