Evikon PluraSens E2608-VOC User Manual Download Page 24

Page: 24 / 25

E2608-VOC

Rev 05.03.2021

* – The new value is applied after restart.

** – Broadcast slave ID 0 can be used to assign a new ID to the instrument with an

unknown ID. When addressing by ID 0 the device shall be the only Modbus instrument in

the network. The device will not respond to the Master command when addressed by ID 0.

*** – This value is dynamic and not kept in EEPROM after a restart.

0x0101

257 /

40258

Raw gas sensor data

0...4095, ADC units

0x0103

259 /

40260

Gas concentration,
gas units

0...65535, gas units

0x0105

261 /

40262

RW 0% value

for analog output 1

-32000...+32000, gas units

User

defined

0x0106

262 /

40263 RW

100% value

for analog output 1

-32000...+32000, gas units

User

defined

0x0107

263 /

40264

RW 0% value

for analog output 2

-32000...+32000, gas units

User

defined

0x0108

264 /

40265 RW

100% value
for analog output 2

-32000...+32000, gas units

User

defined

Summary of Contents for PluraSens E2608-VOC


























Search results

Summary of Contents for PluraSens E2608-VOC

Reviews:

Related manuals for PluraSens E2608-VOC

Brands by name

Popular brands

Evikon PluraSens E2608-VOC, User Manual

Search results

Summary of Contents for PluraSens E2608-VOC

Reviews:

Related manuals for PluraSens E2608-VOC

Brands by name

Popular brands