background image

for Q60 Q30+ Q30

QUEST

QUICK START

Maintenance 

UNBOXING

QUICK START

Contents

Q30+

Q30 Q60

Control box

PRO Headphones

LITE Headphones

Waterproof  

Headphones 

WRX Receiver

Wire Headphones

USB Charger

Elbow Band

Magnetic charge cable

WRX Receiver

LITE Headphones

Waterproof 

Headphones

PRO Headphones

Recharge 

1. Connect the provided charging 

cable to the USB charger. 

2.  Simply  align  the  magnetic 

charging  head  to  the  recharge 

socket  of  the  detector.  The  Li-Po 

battery will not show the memory 

effect, you can recharge it as you 

need to. You can also use a high 

quality  power  bank  to  recharge 

the detector.

OFF/Vol. Down

ON/Vol. Up

Audio 

1.

Wire  headphones.  Remove  the 

protection  cap  and  insert  the 

3.5mm headphones jack. 

2.

WireFree  headphones.  Turn  on 

the WireFree Pro/Lite and activate 

the  wireless  function  by  quick 

press  on  Wireless  button.The 

blinking WireFree symbol 

  ll

i

w

 

light up constantly. 

3.

Pair the WRX with the detector 

jack  headphones  wirelessly.  Just 

put  the WRX  close  to  the  control 

box and quickly turn on-off-on the 

WRX until    light up constantly.

PINPOINTING

To 6.35mm 
Wire Headphones

metal detectors

Do not twist the coil tail and connector to avoid wire damage. 

Do not store the device where prolonged exposure to extreme temperatures can occur to avoid device 

damage. 

Never use a hard or sharp object to operate the touch pad, or damage may result. 

Avoid chemical cleaners, solvents, and insect repellents that can damage waterproof function, plastic 

components 

and finis

hes. 

Secure the audio protection cap tightly(use a coin if necessary) to prevent damage to the audio port. 

Clean the surface of detector every time after you use under water, saltwater or freshwater. Please take 

off the handle from rod and allow the inside of handle dry completely each time you return from 

underwater detecting. 

Pay attention to the sand when change coils on the beach. Sand will get into the connector and void 

the warranty. 

Clean the detector 

Wipe the device using a cloth dampened with a mild detergent solution. 

Wipe it dry. After cleaning, allow the device to dry completely. 

Use a soft, clean, lint-free cloth. If necessary, lightly dampen the cloth with water. 

If using a dampened cloth, turn off the device and disconnect the device from power. 

Gently wipe the screen with the cloth.

NOT POWER ON

Please recharge the detector. Contact your dealer if you can't 

recharge.

NO ALARM

The coil is not connect to the control box

VERY NOISY

NO SOUND

Make sure the Volume is not set to ZERO level and/or wireless 

audio has been activated

FALSING WHEN 

SEARCHING IN GRASS

coil edge on hard objects.

OVERLOAD ALARM

Please turn to BEACH MODE if you are detecting on the beach 

or high mineralized ground.

Shown as Q60 model

To 3.5mm 
Wire Headphones

DETECTING

GROUND 

BALANCING

Trouble Shooting

INSTRUCTION

MANUAL

Quest Q30 metal detector

Summary of Contents for Q30 Series




















Reviews: