EVH MFG HARDEE LR50148 Operator And  Maintenance Manual Download Page 14

Section 4 

Hardee by EVH 

Operation Instruction 

 

 

 

 

LR50148 Long Reach Mower 

11 

 

 

Operation Instructions 

 

During Operation 

 

  WARNING

 

Ensure that all bystanders are clear of the mower 
before starting tractor engine. Objects thrown by the 
mower blades can cause severe personal injury or 
death

 
Before any operation of the mower, be familiar with 
the locations and functions of the unit's controls. Being 
familiar with the mower and its controls will increase 
efficiency and reduce the possibility of serious injury 
or damage to the unit. 
 
The operator should work slowly and carefully until he 
feels comfortable with the mower. Speed and skill will 
be attained much more easily if the necessary time is 
spent to familiarize yourself with the mower and its 
operation. 
 
Get into the habit of completing a walkaround 
inspection before use. This procedure is a simple 
method of inspecting your unit's condition by walking 
around and looking at each component of the unit, 
including the tractor. This procedure has been used by 
airline pilots for many years as a final inspection 
before flight and is also used by long distance ground 
transportation drivers on buses and trucks. During the 
walkaround, you will visually search your units tire 
condition, look for hydraulic leaks, fuel leaks, inspect 
hose condition and condition of hydraulic cylinders. 
Look for loose or worn components, see that all 
guards are in place, check blade condition, look for 
broken or inoperative lights and determine that it is or 
is not operable before use. We recommend that you 
follow this procedure before start up. 
 
 
 

Daily Start-Up Checklist 

 

Check 

Section 

 

Check All Fluid Levels, 
Tractor & Mower, 

For best 

results, use Hardee hydraulic 
oil – part number 23333

 

 

Grease Points 

Page 15 

 

PTO Shaft, Check Grease 

Page 15 

 

Blade Tightness 

Page 16 

 
 

Operating Environment 
 

Application Do's and Don'ts 

There are obvious and hidden potential hazards in 
operating this mower. 

REMEMBER!

 This machine is 

often operated in rough terrain conditions that include 
gullies, holes, slopes and hidden obstructions. Serious 
injury or even death may occur unless care is taken to 
assure the safety of the operator and bystanders in 
the area. 
 
Included here is a list of safety messages, which 
should be followed. Observing these messages and 
using common sense learned from experience help 
eliminate the hazards of operating this and other 
machinery. 
 

  

DANGER

 

Read this manual and the manual for the tractor 
carefully to acquaint yourself with both machines 
before operating. 

REMEMBER

, power-driven 

equipment should be operated only by those trained 
and familiar with the operation and instructed to do so. 
Working with unfamiliar equipment or in unfamiliar 
conditions can lead to accidents. 
 

  

WARNING

 

Before leaving the tractor seat, always engage the 
tractor brake and/or set the transmission of the tractor 
in parking gear. Stop engine and remove key. 
 

  

DANGER

 

Never allow riders on tractor or equipment. Falling off 
can cause serious injury or death. 
 

  

WARNING

 

Worn or dull mower blades can cause excessive 
mower vibration resulting in damage to the gearbox 
and structural damage to the mower. You should 
replace or sharpen blades in pairs. Excessive 
vibration can cause rotating parts to break and fly off 
the mower, causing serious injury or death to the 
operator or bystanders. 

 

  

DANGER

 

Do not modify or alter this machine or any of its 
components or any equipment function without 
consulting HARDEE BY EVH Manufacturing 
Company.

 

Summary of Contents for HARDEE LR50148

























































Reviews: