background image

4

1.  Do not place propane/LP supply tank(s) inside any structure. Store propane/LP supply tank(s) outdoors.

2..  If you smell gas 

• 

Shut off gas supply.

• 

Do not try to light any appliance.

• 

Do not touch any electrical switch; do not use any phone in your building.

• 

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. 

• If you cannot reach your gas supplier, call the fire department. 

3.  This heater should not be installed in a bedroom or bathroom unless installed as a vented appliance.

4.  Solid-fuels should not be burned in a fireplace in which vent-free log set is installed.
5.  Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can 

cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of heater. After 

servicing, always replace screen before operating heater.

6.  If fireplace has glass doors, never operate this heater with glass doors closed. If you operate heater with doors 

closed, heat will build-up inside fireplace and cause glass to burst. If fireplace opening has vents at the bottom, 

you must open the vents before operating log set. Always operate heater with glass doors fully open.

7.  This log heater is designed to be smokeless. If logs ever appear to be smoking, turn off heater and call a quali

-

fied service technician. 

NOTE:

 During initial operating, slight smoking could occur due to log curing and heater 

burning off manufacturing residues.

8.  To prevent the creation of soot, follow the instructions (see 

Care and Maintenance 

page 19).

9.  Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the  vapor from 

these products may create a white powder residue within burner box or on adjacent walls and furniture.

10.  This heater needs fresh, outside air ventilation to run properly. This heater has an Oxygen Depletion Sensor 

(ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available. (See 

Air For 

Combustion And Ventilation

, pages 5-7.)

11.  Do not run heater where flammable liquids or vapors are used or stored under dusty conditions.

12.  Turn off heater before using furniture polish, wax, carpet cleaner, or similar products.

13.  Do not use heater if any part has been under water. Immediately call a qualified service technician to inspect the 

room heater and replace any part of the control system and any gas control which has been under water.

14.  Turn off and let cool before servicing. Only a qualified service technician should service and repair heater. 

15.  Operating heater above elevations of 4,500 feet could cause pilot outage.

16.  Do not use this heater if any log is broken. Do not operate heater if a log is chipped (dime-size or larger).
17.  Do not use this heater to cook food or burn paper or other objects.

18. 

To prevent performance problems, do not use propane/LP fuel tank of less than 100 lbs. capacity.

QUALIFIED INSTALLING AGENCY

Installation and replacement of gas piping, gas utilization equipment or accessories and repair and servicing of 
equipment shall be performed only by a qualified agency. The term “qualified agency” means any individual, firm, 

corporation, or company that either in person or through a representative is engaged in and is responsible for: 

a)  The installation, testing, or replacements of gas piping or 
b) 

 The connection, installation, testing, repair, or servicing of equipment; that is experienced in such work; that 

is familiar with all precautions required; and that has complied with all the requirement of the authority hav

-

ing jurisdiction. 

In areas that prohibit the use of vent-free heaters, the log set has been tested and approved to the ANSI Z21.60 
standard for Vented Decorative Logs. When used as a vented log set refer to additional instructions on page 11.

Summary of Contents for EW18NM


























Reviews: