evertz EQT Series System Manual Download Page 48

Page: 48 / 76

EQT Router User Manual

Page 34

Revision 1.9.1

Set Level Number

Sets the level number for the device (Currently Only Level 1 is
supported).

Set Xpt Restore at Bootup

Sets the XPT to be restore at the bootup.

4.2.10. Viewing / Setting the Clean Switch Configuration (-CS Version Only)

The

View / Set Video Signal Configuration

menus are used to view and set parameters associated with

the video signals. The following chart provides a brief description of the items available in the

View / Set

Video Signal Configuration

menu.

View Clean Switch
Configuration

Displays clean switch status, relay status and companion IP address.

View Clean Switch/Relay
Capability

Displays clean switch capability.

Enable/Disable Clean
Switching for Outputs

Sets the state of the clean/quiet outputs, whether they are enabled or
bypassed (-CS version only).

Enable/Disable Relays

Sets the state of the relays, whether they are enabled or disabled
(EQT-3224 and –CS versions).

Set Companion IP
Address

Sets the IP address of the clean/quiet switch module.



Note: In EQT-3204 the Companion 1 IP address is the IP address of ACO2 Slot 1
and the Companion 2 IP address is the IP address of ACO2 Slot 2.

In EQT-1602 there is only one ACO2 and its IP address will the companion IP
address of EQT-1602.

4.2.11. Viewing / Setting the Video Signal Configuration

The

View / Set Video Signal Configuration

menus are used to view and set parameters associated with

the video signals. The following chart provides a brief description of the items available in the

View / Set

Video Signal Configuration

menu.

View Video Signal
Configuration

Displays input video standard and output cable driver and reclocker
status.

Set Video Input Standard

Sets the input video standard of the device.

Set Cable Driver Slew
Rate Control

Sets the state of Cable Driver Slew Rate to be Automatic or Manual.

Set Cable Driver Slew
Rate

Sets the Cable Driver Slew Rate to be HD or SD only when the Cable
Driver Slew Rate control is set to Manual.

Summary of Contents for EQT Series













































































Search results

Summary of Contents for EQT Series

Reviews:

Related manuals for EQT Series

Brands by name

Popular brands

evertz EQT Series, System Manual

Search results

Summary of Contents for EQT Series

Reviews:

Related manuals for EQT Series

Brands by name

Popular brands