evertz 78908MG-10GE2 User Manual Download Page 9 | Manualshive

Page: 9 / 52

evertz 78908MG-10GE2 User Manual Download Page 9

7890MG Series

Universal Media over IP Gateway for 10 x ASI/SD/HD/3G/GE

OVERVIEW

Revision 0.2

Page - 1

1.

OVERVIEW

The 7890MG-10GE2 is part of the Evertz family of IP Gateway products, which  utilize GE and 10GE
networks for video and data transport.

The proliferation of carrier-grade IP networks and their associated capacity,  flexibility and cost make
them an attractive solution for modern video and data  transport networks. Evertz gateway products
facilitate the bridge between  video and IP worlds, providing the extensive capability, control &
monitoring, resilience and low latency.

The 7890MG-10GE2 has a dual trunk interface which allows for a full 1+1 redundant link.

The 7890MG-10GE2 provides up to 10 input and output interfaces which can be  auto sensed as
ASI/SD/HD/3G/GE. To meet SLA requirements, each interface port can also provide automatic, hitless
switching between the dual links. In the  event of failure or errors of one link, continuity of service
remains uninterrupted.

The 7890MG-10GE2 is available in a compact easy to deploy 1RU chassis and  a 3RU modular card
that can be installed in a 7800 frame to provide high density Video/Audio/Data transport in addition to
up/down stream signal processing.

Features & Benefits:

Video/GE Interface Ports

•

The 7890MG-10GE2 provides up to 10x bi-directional Access Interfaces, 8x auto sensed
ASI/SD/HD/3G/GE + 2x GE/10GE data ports.

•

Auto-Sensing of ASI/SDI/HD-SDI/3G/GE Input/Output Ports

•

Hitless Switching (independent per video port) capability between main and backup network
paths provides for un-interrupted signal reception when network fault occur

•

Up to 2 access ports can be used to interface with existing Evertz ATP products, allowing
transport of a wide variety of other signals including AES Audio, MADI, GPIO, RS232/422

Trunk Ports

•

Dual trunk interface, which allow for full 1+1 redundant link, both 10G or 1G

•

Supports 10GE fiber, 1GE Fiber, and 1GE copper for each interface. Available with optional
1310nm, 1550nm, and CWDM SFP/SFP+ modules

Product

•

Fully hot-swappable from front of frame for low MTTR

•

Comprehensive signal and card status monitoring via four digit card display or remotely through
SNMP and VistaLINK®

•

Fully integratable with ATP Platform using MAGNUM

•

Standalone web page for configuration is also available

«
...
7
8
9
10
11
...
»

Summary of Contents for 78908MG-10GE2





















































Reviews:

No comments