manualshive.com logo in svg

evertz 78908MG-10GE2, User Manual, Page: 48 / 52

Share
Download
evertz 78908MG-10GE2 User Manual Download Page 48

7890MG Series 

Universal Media over IP Gateway for 10 x ASI/SD/HD/3G/GE 

 

Page - 40

 

Revision 0.2

 

WEBEASY

®

 

 

Video Output Hitless Not Ready:

 Triggers when hitless switching is not currently available on the 

selected port. Not having both Trunks plugged in for example could cause this fault.  

 
Trunk A Stream Loss:

 Triggers when the IP stream for this port is lost on Trunk A. 

 

Trunk B Stream Loss: 

Triggers when the IP stream for this port is lost on Trunk B.  

Trunk A Rx Stream IP Change: 

Triggers when a change is made to the IP stream settings for this 

port on Trunk A 

 
Trunk B Rx Stream IP Change: 

Triggers when a change is made to the IP stream settings for Trunk 

B  

 
Port Select: 

Brings up the SFP Fault SNMP Error Traps for each SFP/SFP+ Port.  The check boxes 

on the left will enable or disable these faults from being sent to the SNMP Fault Trap log.

 

 
Traps 

SFP Type Incorrect:

 there can be a maximum of two simultaneous input streams to be sent to the 

output Port being selected.  These input streams can appear on Trunk A and Trunk B 
simultaneously.  Typically these will be main and backup input streams. 

 
SFP Rx Power Low: 

SFP Optical Receive Power is Low.  Threshold is adjusted in the SFP Monitor 

TAB 

 

 

SFP Ethernet Link Status: 

SFP Ethernet Link Status Up or Down 

 
SFP Present: 

SFP Presence Detect

 

 
Trunk Select: 

Brings up the Trunk Fault SNMP Error Traps for Trunk A and Trunk B.  The check 

boxes on the left will enable or disable these faults from being sent to the SNMP Fault Trap log. 

 
Traps 

Trunk Error:

 Triggers whenever errored seconds appear on the selected Trunk Interface. 

 
Trunk Severe Error: 

Triggers  whenever severe errored seconds appear on the selected Trunk 

Interface. 

 
Trunk Link Down: 

Triggers when the trunk link is not active. 

 

Trunk Bandwidth Higher: 

Trunk bandwidth is greater than max bandwidth threshold set in Trunk 

Port TAB -> Bandwidth High Threshold. 

 
Trunk Bandwidth Lower:

 Trunk bandwidth is less than min bandwidth threshold set in Trunk Port 

TAB -> Bandwidth Low Threshold. 

Summary of Contents for 78908MG-10GE2





















































Reviews:

No comments