evertz 7707BPX Manual Download Page 9 | Manualshive

Page: 9 / 24

background image

7700 MultiFrame Manual

7707BPX Optical Bypass Protection Switch

Revision

1.6

Page-5

2. INSTALLATION

The 7707BPX comes with a companion rear plate that has three SC/PC (shown), ST/PC or FC/PC optical
connectors and a six pin terminal strip. For information on mounting the rear plate and inserting the
module into the frame see the 7700FR chapter section 3.

Figure 2-1: 7707BPX Rear Panel

INPUT A, B:

The two SC/PC, (shown), ST/PC or FC/PC female connectors are wide range optical inputs
that accept wavelengths accommodating standard 1310nm, or 1270nm to 1610nm CWDM
transmission schemes. The A connector is for the

Main

input and the B connector is for the

Standby

input.

OUTPUT:

This SC/PC, (shown), ST/PC or FC/PC female connector is the output from the switch.

«
...
7
8
9
10
11
...
»

Summary of Contents for 7707BPX

























Reviews:

No comments

Related manuals for 7707BPX

Brand: 3Com Pages: 128

Brand: 3Com Pages: 2

Brand: 3Com Pages: 422

3CR16708-91 - OfficeConnect Managed Switch 9

Brand: 3Com Pages: 4

Brand: 3Com Pages: 5

Brand: 3Com Pages: 30

Brand: 3Com Pages: 36

Brand: 3Com Pages: 4

Baseline 2226-PWR Plus

Brand: 3Com Pages: 77

Brand: 3Com Pages: 570

OfficeConnect WX1200

Brand: 3Com Pages: 28

Baseline 2226-PWR Plus

Brand: 3Com Pages: 4

CoreBuilder 6000

Brand: 3Com Pages: 31

OfficeConnect 5

Brand: 3Com Pages: 2

OfficeConnect 3C1670500C

Brand: 3Com Pages: 18

TNS5800-8GP16GT-P24VDC

Brand: 3onedata Pages: 3

Brand: Enttec Pages: 22

Elinx EIR418-2SFP-T

Brand: B&B Electronics Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands